1068254981 Kenmore Freezer - Instructions

After searching online to diagnose the issue with my refrigerator being warm and the freezer being cold and not shutting off to defrost I decided to get the defrost timer kit. The kit arrived within 2 day. With the directions included, after unplugging the appliance for safety, I installed it relatively quickly with only a screwdriver . I then plugged it back in and it immediately went to defrost. I thought, wow I have it fixed. Well unbeknownst to me it still didn't cool in the fridge area. After doing more internet research I found a suggestion to unplug the fridge for 24 hours to unthaw ice that may be lodged between the freezer and fridge that is blocking the distribution of cold air into the fridge. After doing this, it now works like a charm.

Followed instructions from ideoo

removed screw on top cover emptied ref door remove 3 top screws holding bracket on top. lifted the door then remove old cam then reassembled.

Remove top henge, lift door off bottom henge, take off old plastic closer put on new one. Door works great now

replaced relay switch
when I finally got started to do the repair it took 15 minutes my biggest delay was no instructions were sent with the part and it took time to get some

Replaced very easy.

Reviewed Youtube video as a reference. Unplugged refrigerator. Removed old defrost timer. Matched the color of the wiring harness to the diagram that came with the part. Attach new part to wiring harness.

Eased the putty knife under the edge of the switch housing and pried it off. Pulled two wires off the old terminals and hooked them onto the new one and reinstalled into the refrigerator body.

I followed your on line video, that was a fantastic help. Easy as 1,2,3. I used the tools he recommended and followed his steps. I replaced the cam on the door and on the bottom pin, its works like new.

We looked up the problem online with the model number of the refrigerator. We ordered the part and followed the video installation that was sent with the order and was found online prior to purchasing

bulbs were not burnt out. received the new switch in a few days. watch the short video, was good to see how it comes out. used a putty knife to release the defective switch, removed wires put them on the new one and posed the new switch back in. Not bad Part cost $11.00 7 dollars shipping so for 17 bucks it works great. nice to see what is inside the refer!

Your on line video was fantastic, it led me all the way through the repair. As they say, "A picture or video is worth 1000 words". I wish everyone had instructions like you. Great Job!!!

repair was easy. watch the video

When we got the part, we read the instructions, which were easy and very clear step by step. Taking the old part off took most of the time, it was attached a little differently than was described in the video and the instructions for the part. Once we detached that, the replacement part went in very easily and quickly. It took a short while for the cycle to start, we were actually a little worried that it wasn't going to work. Then it started cycling. After the first day the freezer had started icing up, we took a blow dryer and melted it and waited. It hasn't started freezing up again. The refrigerator is keeping the proper temperature and the freezer is also working properly, it's been a week. We seem to be obsessed with going out and checking to see if it's working but I think it's a success. Doing this ourselves only cost $26.00. A huge savings if we had hired someone else to repair it for us. We will definitely choose this option with any other appliance that needs repair. It was easy and simple to find the correct part thanks to the website. And the video tutorial was very informative and helpful.

first confirm that freezer is cold. if is frozen solid it needs to be defrosted. take the freezer items out,take shelf out, bottom cover, 2 screws. then ice maker, 3 screws and unplug wires. then back panel 2 screws. In refrigerator compartment were the controllers are located, look under it you will see 1 hole, insert a flat end screw driver and turn clockwise till it stops. this action will turn on your defroster, also the compressor will stop. is the heater melting the ice? if so soak up water and clean tray, use hair dryer in drain hole to aid in the defrost, check tray under fridge and if its dry keep defrosting. it should take half an hour. now take the flat head screw driver and turn the defrost timer clock wise out of defrost mode a quarter turn or so. the compressor should come back on, soon after the fan in the freezer compartment should also come on. this steps lets you no that the defrost heater works, fan works and drain hole is clear. if its defrosted place parts back in the reverse order. if not defrosted replace heater or mother board. in refrigerator compartment were the dials are located their are 2 screws, one on the left and the other on the right side take them out, the cover will drop down, you will find wiring schematics you will need them to install defrost timer. is timer making ticking sound? if no replace timer. new timer will be different from original so follow instructions that come with it. timer is above were the hole is located. the plastic hold downs will break when you try to take them off, unplug fridge, lift timer out and remove from wire harness. the new timer has a black wire that slips over either 1 or 2 depending on color of wire on the wire harness. check schematics. some silicone adhesive will keep unit in place, ad some into the plastic shaft prior to installation, plug wire harness return wiring instruction along with new one inside of cover, plug in fridge, turn defrost timer clock wise with flat head screw driver making sure that you hold timer from above so it wont move. did compressor come on?. put all paper work inside of cover before installing cover