1068254981 Kenmore Freezer - Instructions

I noticed that the refrigerator was having trouble maintaining temperature. Thought it might be time for new one until I found out that a new frig was $5k to $7K. Just happened to notice that the light switch didn't look quite right (was not sitting sqaure to the door). Once I pressed it it came loose. I then realized the the lights were staying on (50 watts of heating). Replaced the switch and the frig started working like new.

I followed the video instructions available on the net. Hardest part of the job was getting up off the floor after I disconnected the water line. I'm 90 years old

I was quoted $212.00 by a service co. to make this repair. When I investigated online @ Part Select, they had all of the parts shown on schematics of each section of the refrigerator/freezer (side by side)with part numbers shown. It was easy to find the necessary parts.The cam kit came as a package for both doors and cost $12.00 plus shipping. Installation instructions were included.It took me an kour to make the repair. The hardest part was removing all the condiments from the shelves and remembering from which shelf they had to be returned. Net savings $200.00

Removed the door, installed the lower cam & re-installed the door. Diagram & parts list correct. An easy repair.

Unplug appliance. Socket wrench to unscrew two screws. Module drops down. disconnected two press-on wires by prying off with screwdriver. Removed old switch. Press-fit new switch. Reconnected two wires (color coded). Screwed module back in place. Plug in appliance.

Pry old switch and pull out. Disconect two wires. Put two wires on new switch, must be inserted right and connections not loose. Put switch in, making shure wies do not come off and snap in place

We dealt with this problem for well over six months. Last week while visiting our home my mother tried to schedule a repair man to come out. Upon hearing this conversation i urged her to hang up the phone and let me fix it. This prompted me to go on line and find the three dollar part needed to fix it. With the help of a friend to lift and hold the door i unbolted the black closer piece and replaced it with the new one. This whole process took less than 10 minutes and completely fixed the problem. The service visit would have cost upwards of $80.00 so this was well worth the two days shipping i paid for.

Part was easy to order, delivered quickly, installation very easy. Just unplug the unit, pop out the old swich using a screwdriver, disconnect and reconnect leads and pop switch back in. Definitely recommend that you can do it too.

Used a screwdriver to pry loose the old switch, swapped wires to the new switch and pushed it into the opening. Took about 2 minutes.

Great service. Unpluged old switch and pluged in new one. Works great

A very cold and brittle switch in a 17 year old fridge. Used screwdrivers to pry out with some resistance Had to cut the molded plug in half and split wires, because replacement contacts were farther apart than the original. End result, works great.

removed the 2 screws that held the panel in place, had to reach up and push on locking tabs to lower trhe front of the panel. was able to then push on the locking tab of the switch to release it. removed the wires, replaced them onto the new switch, and snapped the switch into place. the rest was reverse of the uninstall process.

removed door,removed worn part and replaced with new.

1. Used fine tip marker pen to draw outline of upper hinge position

2. unloaded food from door

3. took decorative cover off upper hing mount

4. loosened 3 screws (not completely) and lifted up upper hinge to permit upper door pin/hinge to come free.

5. lifted door off lower hinge.

6. remove broken pieces, cleaned, put in new pieces, added small amount of grease

7. put door on bottom hinge.

8. put top hinge into door

9. snugged up three screws in top hinge plate.

10. had to loosen top hinge screws and tap hinge plate around to get door to close by itself when about 1-2 inches from being closed

Best part was PartSelect save me bunches of money and got parts quickly

it was a simple repair once I located the part I had to replace . I really like your speedy delivery of the part I needed Thank you Pat Crotty