58714000102 Kenmore Dishwasher - Instructions

PartSelect provided the perfect place to order the parts I needed. Illustrated parts breakdown on PartSelect was excellent and the correct part(s) were identified and ordered with no difficulty. I would recommend PartSelect to anyone.

Remove old spray arm and pressed the new part into place. Let the dishwasher run and the load came out very clean. Overall very pleased.

I foloowed the others who repared the same item. I really appreciated their help and input. The only thing I would add is when they said that you only have to remove the bottom 2 screws on the inside of the dishwasher door they are absolutely correct. But don't look on the very bottom of the door like I did. They are on the inside of the door, facing inside. The bottom screw on each side. Thanks for all the help.

Found your website, red the reviews, followed the simple instructions provided by others that had had the same problem and repair was complete in less than a minute. No tools needed. I am a handy girl and tackle a lot of repairs/projects, this is the first time that the job was actually easier than stated. Thanks for providing a good porduct, at a decent price WITH LAYMAN INSTRUCTIONS!!!

Unplugged the dishwasher and pulled it out. Tipped it down on its side. Removed the old and replaced the new. Re-installed and replugged it. Ran a test. Checked for leaks.

Remove and replace the door gasket. Removed the 6 phillips head screws holding the top panel cover. This gives access to the latch assembly. Remove the two screw holding the latch in place. I removed the four wires one at a time with needle nose pliers and plugged them on the right spade of the new latch assembly. This assures getting them in the correct position. I then mounted the latch with the two screws and installed the cover with the 6 screws. Job done, piece of cake.

slide out dishwasher. remove 2 screws holding motor/pump assembly in. slide out motor/pump bracket. disconnect electrical connection from motor. pull motor/pump assembly out. install new 'O' rings on new motor/pump assembly. (lube with liquid soap). install assembly. slide in motor clamp and install 2 screws. reinstall dishwasher. run test cycle. Fixed!!

I went to your website found part# and parts diagram and ordered parts . I picked standard shipping . That evening e-mailed me they were instock and shipped also gave tracking # thet parts were here the next day.I removed the front dec panel then the 4 nut& bolts holding door to hinges(with door in closed position).Then I removed the 2 screws holding the hinges to the frame/axle. Replaced hinges with new ones .Put screws back in frame/axle . Put 4 nut and bolts back to secure door to hinges . Then i reinstalled under counter put new wheels on lower rack . I then filled it with dishes and ran a long cycle checked for leaks THEIR WERE NONE!!! THANK GOD !! Job complete, Thanks parts direct for a well designed website and detailed pics and parts#. TIM

Intuitive repair if you are one of those people that take things apart & put them back together for kicks. Nothing fancy about this repair, as all the parts have no adjusting. Remove the 6 phillips heads screws on the inside of the dishwasher panel. The front electric panel comes off, leaving the inside exposed with the wires. Unhook 4 wires to the handle. Remove (2) star shaped screw headed screws. (The most difficult part if you don't have this bit.) New handle can only go in one way. Re-attach wires & screw panel back on. The latch required pulling the dishwasher out a couple inches from under the countertop to access the mounting screws. The dishwasher is held in place with 2 screws into the countertop/or side cabinet. Slide dishwasher out. Remove 2 screws and replace. Once again, there is only one way the latch can be installed. All is good, and easily accomplished in 5 minutes....if you have the "star" bit, which does come in a couple different sizes.

#1 rule, make sure you valve off the water before removing any hoses. Remove wire trays inside dishwasher and then pull out dishwasher far enough to disconnect water line and power cord. Remove center piece and screen covering sump inside the dishwasher. Turn dishwasher on its side and remove hoses to sump and pump. Disconnect power to sump pump. Loosen retaining nuts that secure the sump and remove. Replace old gasket on sump with new. Turn dishwasher upright. Be careful with placement of new gasket when reinserting sump so that the gasket doesn't come out of position and the sump is centered properly. Secure with retaining nuts from bottom. Reconnect power connector and hoses to sump. Pour enough water into the dishwasher to verify gasket doesn't leak... look with flashlight under dishwasher for signs of water dripping from sump. Reinstall screen and centerpiece in sump inside the dishwasher. Reconnect water line and power cord. Run through wash cycle while monitoring for leaks under dishwasher. Reinstall wire trays.

Piece of cake as long as you get the gasket installed properly and the sump centered correctly... do not overtighten the retaining nuts or it may force the gasket out of position when the screen is secure with the center locking piece over the sump.

It is rather easy to repair. After you remove the screws that secure the top of the dishwasher to the countertop you can slide the disherwasher out far enough to gain access to the hose. The hose pulls off after you slide the spring clips down the hose far enough so they no longer grab. Then simply reverse the order and you're done. Less than 30 minutes and you should no longer have to hand wash your dishes!

The repair went very easy. Just opened the door , and pulled out the worn seal. Lined up the new seal and carefullly pushed new seal into place. Seal pushed in very smooth.

Delivery of this part was really fast. I ordered very early on a Thursday morning and the package was at my house Friday afternoon. This was a pretty simple repair. First you take the front panel off. There is an upper panel where the controls are and a lower finished apnel. Open the door, the screws are on the inside face of the door. Put a towel on the floor so the panel doesn't drop and scratch the floor or get damaged. Unscrew the panels so you can get to the door handle, it is held in with two torx screws (star shaped head). Take the handle off and remove the wires on the door switch. Installation is the reverse, mind that you install the wires on the right leads. The handle works better than the original ever did.

I took out 6 screws, the face plate just hung down. Make sure the breaker is off. there were two screws that held the switch and handle in place took those two out. Disconnected the four wires on the microswitchs and placed them on the new handle. Put the diswasher back together. Turned breaker on and worked great. But it started to leak. This is why they give you the gasket. The new latch does not always match to the same seal o the gasket. Replaced the gasket took less them two min. Ran the dishwasher again no leaks and the handle you can use one finger to unlock.

Took off front door panel with two screws. Found the part in the door. took it out and slide the new part in. My husband screwed the screws while I held the door in place. If I had known it was so easy to do I would have done it as soon as I got the part but I waited for my husbands help.