66513192K902 Kenmore Dishwasher - Instructions

1.Check the lines for any obstruction. Gunk can easily build up. I have used the dishwasher for approx. 10 years. I do rinse/scrap dishes prior to loading.
2. Drain all remaining water.
3. Unplug the dishwasher.
4. Grab a towel and proper screw driver. Unscrew the bottom protective plate. Remove the insulation plate.
5. The drain pump is located to the bottom left. Have your towel under it. Unplug it gently. Turn counter clockwise to remove.
6. Install the new drain pump (reverse order)
7. Return the insulation plate. Screw back the bottom protective plate.
8. Plug in

After pulling the dishwasher out from under the cabinet, I found it underneath near the back right side. I disconnected the old thermostat, unscrewed the clamp holding it into place, put the new thermostat in, screwed it back in and replaced the two plugs. Then I pushed the dishwasher back into place, and it initially didn't work until I found an online forum that was able to identify the reset command for my dishwasher (for the WDT710PAYM4, press any three buttons in a sequence of 1 2 3 1 2 3 1 2 3. After completing that all the lights lit up, and I shut the door leaving it for half an hour) Once the reset finished, the heated dry worked like it was suppose to.

Actually, the repair was very simple because of the you tube video demonstrating the repair. This made the repair very easy. I repair/replaced both springs and links

No brainer

simple...a female did it!! Dealing with PartSelect was so easy...your was the only web site that made it super easy to find my part. Placed order and paid for it...part arrived the next day!! Sent web site link to hubby too. When we need parts again for any applicance in our home, we will check your site out first!!

I first turned the power off to the dishwasher. I then used the star bit to loosen the screws on the sides and top. Note that the 4 top screws are longer than the side screws. Once the screws were loose I used a clamp on each side to hold the door cover in place. Once the screws were removed, I released the clamps, raised the door then lifted the outer cover off. I then peeled the insulation back from the top to expose the dispenser. I used a small socket to remove the screws for the dispenser. I released the plug with a small slotted screw driver. I then exchanged the dispenser with the new unit being careful to correctly reinstall the black cover over the top. I reinstalled the door cover, being careful to tuck the insulation back in place. I then installed the screws using the clamps to hold the door in place during the reinstall.

Removed new from box and installed rollers as instructed that's all there was , very easy.

Rolled out old, rolled in new.

You need to pull the unit out to get access to the spring connected to the rear leg frame. Use the everything in the kit. The rollers are upgraded and will guid the cable better.

The new lower spray arm fit right into place. All set, and I will always check to see if it is sitting properly!

A Mouse friend had seen fit to chew through the original drain line. I used my Model Number, and was able to order the correct part . It arrived the next day. The job itself is fairly straight forward. You will need to access the rear of the machine. This may include shutting off, and disconnecting the water supply line. (Adjustable wrench). Mine is under the sink, on the "Hot" side. You may also need to un-plug the unit. (recommended) . A pair of (Pliers) will be needed for the spring clamp.

Removed old rack and and removed old rollers and installed old rollers on new rack as they work better than the new rollers sent with new rack

Since I had manual from initial installation I knew code meant heater was malfunctioning. Went to Sears, Lowes..no parts to repair. Instructed to go to appliance repair shop, closed of course...ordered online instead here and received in 2 days. Repair took 20 minutes. Super easy! Do not attempt to use adjustable wrench to tighten, use socket set as plastic electrode casings will be compromised. Takes some tork. Probably saved $100-$150 repair call. Wife was pleased. I was suprised how easy.

Grabbed old seal and removed it.(notice how seal was situated in slot)

Pushed new seal in slot that held old seal. close door.

If dishwasher still leaks you put the seal in backward (I did!)remove seal reverse it and reinsert it.

I watched the video identifying the part and the procedure to make sure I could handle this. The phone attendant was also very helpful in making sure I ordered the correct part,which arrived in one day (amazingly). Everything was clearly described in the instructions and if you have done electrical work this would be relatively easy. You will need a specific screw driver bit to open the control panel but everything else is straightforward, just follow the instructions. Works perfectly now (I needed a new control panel about a year ago and Kenmore charged me $229 but it was just over a year since then....) PartSelect is a great service!