7WRS22FDBF00 Whirlpool Refrigerator - Instructions

When the filter arrived, I removed it from the package.
Upon reading the instructions, I removed the old filter.
When I removed the old filter I NOTICED HOW IT CAME
OUT SO THAT I COULD HOLD THE NEW FILTER IN
THE SAME POSITION AND REPLACED IT WITH THE
NEW IN THE SAME POSITION. When I closed the cover
door, I went to the display panel and reset water filter display.

Checked the water line from the wall to the supply port of the inlet valve and it was suppling water but no water beyond the water inlet valve, So I ordered a new inlet valve and installed, and it fixed the problem. Inlet valve supplies water to the ice maker and water dispenser filter housing. Partselect videos and you tube installation videos very helpful. Partselect troubleshooting guide also very helpful. Great company

Shut off water supply. Unplug refrigerator. Removed lower back cardboard panel. Removed two screws holding inlet valve bracket to side frame. Pulled valve out far enough to gain access to water lines and electrical connectors. Used 9mm open end wrench to press in collars to remove water lines from inlet valve. Used small container to catch water dripping from lines. Removed defective valve and replaced with new one by first pushing water lines into respective openings, make sure they are fully seated. Reconnected electric wires. Installed inlet valve on side frame. Replaced back panel. Plugged in power cord. Opened water supply. Flushed about 2 gals of water through system. Note: water may not flow immediately due to air in water lines.

Refrigerator side top unscrewed hex screws unscrewed Phillips screws remove circuit board unplugged connects and installed new board in reverse order

Put new drawers in

I removed the cardboard back then using a nut driver removed the three mounting screws, removed the old fan/motor and installed the new one, installing the three screws and replacing the cardboard cover.

My big problem was getting the right parts. Don't ever order refrigerator parts using the refrigerator model number. I did and got the wrong part, sent it back and talked to the parts lady and ordered again describing the error, the needed parts shape etc and she sent me the exact part I had sent back. I sent it back and removed the fan motor to get the part number, called and ordered by number and got the right one. Hallelujah!

Followed the u tube directions disconnect the power to the refrigerator remove the Ice cube pan place flat head screw driver under the front tabs push in to release the tabs pull down on the light release the back tabs from housing pull the light down from the housing disconnect the plug from the burned-out diode replace with the new diode light and repeat the same instructions in reverse to reinstall the diode light. The diode light in the freezer controls all the light in the refrigerator and freezer all should now light up.

After lots of internet exploring and diagnosis, the icemaker comes right out, and with three screws out and in, the job is all but done. Don't pay anyone for this repair!!!!!

removed old shelf support after taking out the glass and support. New part was a perfect fit that was a "shap: to put in.

As cookbook authors and publishers, my husband and I depend on our appliances. When our icemaker would no longer work, it was imperative that we repair it as quickly and ecomonically as possible. We had used PartSelect.com earlier to order a part to repair our Jenn-Air stove top and had great results. So, rather than paying a repairman four times or more the cost of the part, we ordered the part and my husband installed it. It took less than 30 minutes to remove the broken auger and install the new one. THANKS PartSelect.com -- we'll use you for all appliance parts needs.

I removed the screws that attached the drum housing to the bin. I detached the auger & removed the broken drum assembly, turning the auger to the right, opposite what I thought it should be. I slipped the end of the auger into the new bin coupler & put it in place at the rear of the bin. Next I slipped the auger drum into place & tightened it to the left with a socket wrench. I screwed the drum housing to the bin, put the bin back into the freezer & I now have ice through the door again. Easy repair even for me, a 60+ woman.

took old bin out replaced with new , two minute job
Parts select is an easy co. to do business with THANKS Andrea

replaced

Technician at ASK suggested replacing ice maker. Ordered new ice maker(prompt delevery)then noticed it came without wire arm and white platic "flag". Ordered arm and "flag", replaced all old with new and seems to be doing well. Perhaps all I needed was the plastic "flag" on the limit arm wire. Will never know. The new icemaker wiring had short wires and a connector. Old ice maker had no connector so the short wires were removed and the old wires plugged into the ice maker. Mirror was required in order to see the side wall mounting screws. Very narrow work area, tiny freezer side.

Emptied draw of contents pulled draw out and inserted new drawer....easy pea-zee