9117318710 Kenmore Range - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Hinge broke on range. Oven door was very hard to open.
Followed the instructions from the video. The repair was really easy and quick.
Parts Used:
-
Ricky from LAWRENCEBURG, KY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers, Screw drivers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven igniter didn't work.
The bolts were below the base of the oven, and very difficult to remove and replace. The directions were not applicable to our unit. The good news was the igniter was correct, even though we had to adapt the bracket.
Parts Used:
-
Jacklyn from HOWARD CITY, MI
-
Difficulty Level:Very Difficult
-
Total Repair Time:More than 2 hours
-
Tools:Pliers, Screw drivers, Socket set, Wrench set
2 of 5 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven burner would not ignite
Removed shelves and floor of oven. Removed burner unit to access screws attaching igniter to burner unit. Disconnected wires of igniter. Put new igniter in place and reinstalled burner unit. Reconnected wires using supplied wire nuts. Tested unit. Reinstalled oven floor and shelves once successfully tested. Cooked Pizza.
Parts Used:
-
David from Elizabeth, CO
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers
1 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken Hinge
Easy Repair. Remove the storage draw under the oven. It lifts out. Lift oven door off of hinges. Remove 3 screws & unhook the spring. Reverse the procedure with the new hinge. Good as new.
Parts Used:
-
Martin from Fords, NJ
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
1 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven door only opened 1/4 of the way
After reading the other DIY's directions, we explored how to remove oven door. When the part came in, my sister who was visiting, removed the oven door (30seconds), removed bottom drawer (30 seconds), noted where spring was attached, took off screws and spring, installed new hinge with roller, took a minute to decide if the new hinge came through the back or the front (front), she reattached the spring and screws. Put door back on and then struggles to put the drawer back into place. Total time less than 5 mintues, most time spent on returning bottom drawer to its home. Thanks part select for helping me not burn my self every time I try and get food out of the oven!!! I open the oven door all the way and am so delighted!!
Parts Used:
-
Beth from Emerald Drive, NC
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
1 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
defective spark module
used nut driver to remove old module and 10 minutes the cooktop was back in operation
Parts Used:
-
James from Reseda, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver
1 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven would not come on.
I changed out the old ignitor with the new one. New ignitor fit perfect on old mounting bracket. Attached the two wires and that was it.
Parts Used:
-
Joseph from Berkeley Springs, WV
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
1 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
oven igniter would not heat so gas valve would not open
removed the old part with socket set and replaced the part with a fresh one. turned on oven, igniter heated up and oven lit.
Parts Used:
-
Nicholas from Elkridge, MD
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers, Socket set
1 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken door hinge
The part arrived on timed and fit perfect. The repaired took 1/2 hour and everything works perfect. My wife thinks I am the best
Parts Used:
-
Dave from Glenview, IL
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
1 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
oven wont turn on but broiler does
-
Nick from south st. paul, MN
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
1 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Igniter doesn't glow
I'm still repairing. The igniter was replaced with new but it still doesn't glow. I'm waiting for a schematic that is being mailed to me from GE. In the meantime I have borrowed a test instrument to check that the system is hot when the BAKE button is pushed. The controls light up as expected but no glow. The BROIL igniter glows when activated, lighting the broiler. The new Ignite was packaged very well so it isn't suspect. I LEFT YOU FOR A FEW HOURS. I tested the electrical with a meter and got zero voltage. I removed the wire nuts and using two alligator clips I connected the meter to the bare wires coming from the oven wall. I then hit BAKE again and BINGO! Replaced the defective wire nut and now the igniter is happy as a clam. --- Thanks for your interest and for expediting the material.
Parts Used:
-
JAMES from GARDEN GROVE, CA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:More than 2 hours
-
Tools:Nutdriver
1 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
oven broiler worked but oven would not ignite
Remove oven door,just open slighty and pull door up no tools.Take oven draw out.Remove oven floor held by two nuts in rear.You will now see the igniter,remove two screws holding it and the one screw holding the long tube at the front.The best tool I used was 1/4 drive socket set with a 6" ext.I did'nt need a new bracket that came with the part and I cut the old igniter wires and wired in the new one because it had a special connectors.If your are a handy person,its EASY.
Parts Used:
-
Leonard from Bayside, NY
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Socket set
1 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Igniter would not start
1.Took out the metal pan.
2.Removed the ignitor bracket.
3.Disconnected the two wire mount the new ignighter.
4.Connect the new ignighter wires to the wires still attached to the valve.
5.New igniter glow wonderfully.
2.Removed the ignitor bracket.
3.Disconnected the two wire mount the new ignighter.
4.Connect the new ignighter wires to the wires still attached to the valve.
5.New igniter glow wonderfully.
Parts Used:
-
Emir from New York, NY
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
1 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven would not light
It took a while to determine the cause of the problem because I was not familiar with gas appliances.After finding the problem I ordered a new igniter. The part was there in two and a half days!! I had it partly apart when the part arrived so it only took about 30 minutes to complete the repair. I would recomend PartsSelect to anyone. I have never had parts come that quickly.
Parts Used:
-
Douglas from Clare, MI
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
1 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven would not light
Replace igniter in oven. It was a simple repair and only required that I unplugged the power cord from the unit, remove the base and 2 screws holding the igniter.
Parts Used:
-
Harold from Delran, NJ
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Pliers, Screw drivers
1 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!