91195181890 Kenmore Range - Instructions

Before ordering, I took the element out to make sure I could do it. A flashlight was helpful.

I flipped off the circuit breakers to the stove, removed the racks and lifted off the oven door. Not having a nutdriver or socket set, I used a 6' crescent wrench to remove the two screws which hold the element to the back of the oven. I carefully pulled the element out until the spade connectors to the wires were exposed. I wiggled the connectors apart. I had pliers handy, but didn't need them.

I connected the new element to the wires and gently pushed the two connected prongs through their holes, trying not to disturb the insulation. I put a little WD-40 on the screws so they would go in easier. After tightening the screws with the crescent wrench, I replaced the racks and door. I flipped the circuit breaker back on and reset the clock. It works as good or better than new.

Easy

First I removed the two screws that hold the element in place, I then pulled the element out about three inches, and it shorted out on the main panel of the back of the range. I then went to the breaker box and flipped the switch so I could tell my wife "Yes, I had turned the power off."

Disconnecting the two wires and reconnecting them was a simple operation after I cleaned my pants from the electrical short.

Re attaching the two-screw panes to hold the element in place finished the project.

.First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires and reversed the procedure with the new element very simple.

1. Turned off power at the breaker box. Removed oven door from oven, and removed bake racks. Determined replacement element from PartSelect was correct. Inspected new element. Using meter, determined new element was OK via continuity test. Gathered all appropriate tools to do the job.
2. Using 1/4" nut driver, removed two retaining screws at back of oven that secure element
3. Pulled bad element out a few inches from oven back to reveal wires and spade connectors
4. Using screwdriver, pushed off electrical connectors from bad element and removed element
5. Inspected wires and connectors and determined them to be OK
6. Installed new element in reverse of above. Inspected oven controls and determined them to be OK. Turned on the breaker. Tested oven.
7. Baked a delicious chocolate cake

My dealer was unable to find the part even with a model number. Your accurate drawings allowed me to select correct part. It was a perfect replacement in every way and cheaper (by $10) than the dealer. Also quicker.

I turned off electric to the stove. In the oven, I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. After unpacking the new element, I placed it in the bottom of the oven, reconnected the two wires, and gently fed the wires back into the back of the oven. I then secured the new unit to the oven wall with the two screws.

Rating: 5 Stars!! We cut the power, removed two screws disconnected the two wires (just pulled them out of the covers) from the old element and pushed in the new ones. It didn't take longer than 10 minutes!

This is the first time it's been as easy as promised! Great customer service in addition to easy and reasonable prices!
Thank you,

1st, Turn off the stove at the electrical box. 2nd, Remove the oven door by opening it to the first stop, and then pulled it straight up. 3rd, Remove the 2 screws using a 1/4" nut driver. 4th Pull the old heating element straight out, until the two wires that attach to the element are out 3" from rear oven wall. (Note: Place a peace of tape around each wire before disconnecting from the element. this will keep the wires from falling back through the holes). Remove the wires from the old element and remove the old element. 4th Place the new element into the oven, place the wires onto the new element. Then reverse the order of removal for new element install, for the repair. Less than 10 minutes.

Very well, I made a mistake with the model #. So I had to return and reorder .

Watched youtube....

This is how I did it--but I would strongly recommend you do step 4 first, and skip step 3! Remember, because 240V circuits have 2 "hot" wires, they may be "hot" (120V to ground) even when switched off!

1. Removed the mounting screws with a nut driver.
2. Pulled out the old element. BARE lug connectors on loose wires came out with it.
3. Watched an impressive show of sparks.
4. TURNED OFF THE CIRCUIT BREAKER.
5. Separated the connectors. Had to use pliers on the one I "fried".
6. Connected new element (connectors pushed together easily.
7. Reattached with screws
8. Turned breaker back on.

Watched youtube. Easy and fast!

Very simple. Two small hex shaped screws hold the unit to the back of the stove. Remove those with a small socket wrench. Rachet type makes the job easier. Gently pull the element from the back of the stove. Remove the two push-on wires from the element. They simple pull off. The elements have supporting feet toward the front. Those must be down to rest the element on the bottom of the stove. Replace the push-on wires, push the element back into the holes in the rear of the stove and screw the small hex shaped screws back into the oven wall. The job is done.

Using a wrench, removed old element and simply installed new one - took less than 10 minutes and the oven was working again! Best part was how quickly the item reached us - ordered it on a Wednesday afternoon and had it by Friday afternoon, with no expedited shipping - Great Service!