FBD2400KB10B Frigidaire Dishwasher - Instructions

I recently bought a vacation home in New Hampshire, and had a very detailed home inspection performed. The dishwasher unit was checked out to be in fine shape. Before moving in, I had all the hardwood floors refinished, including the kitchen, and everything looked great. After moving in and using the dishwasher twice, it developed a major leak coming from the bottom of the unit. "Here goes more money that I don't have, to hire an appliance repairman to fix this leak!" I decided to take the bottom kick panel off the dishwasher to see where the leak was coming from. It was coming from the the connection of the heater element at the bottom of the dishwasher. I found a brass nut had been cracked and wouldn't stay tight any more. I ordered the replacement nut from Partselect, RECEIVED IT THE NEXT DAY!!!!! using regular ground shipping, and installed the new nut using a socket set, and tested the unit. No more leaks!! Partselect saved me at least $150.00 on a service call for a $3.50 part. I'm not the handiest guy around, but even this was easy!
I also scored big points with the wife on my handyman repair! Thanks Partselect!

Greg

Easy as pie. I tokk the screws out that held the dishwasher to the counter top out. Then removed the screws holding the strike in place, inserted the new one, installed screws and then rescrewed the 2 screws backintothe countertop. Job done. All told 5 minutes.

First I pulled out the old gasket and replaced with the new one. The new one is too long on purpose but only had to be trimmed a little for a perfect fit. Very easy and now no leaks.

I used a screwdriver to remove melted spray arm. Then snapped the new spray arm into place. It was an easy repair thanks to the correct part from PartSelect.

Isolated the leak and found the nut had split thereby allowing a loose seal and water penetration. Ordered 2 nuts just in case the other goes and the installation was easy. Unplug the unit, remove baseplate, remove screws under the countertop, and slide the unit out a bit. Use needlenode pliers to remove terminal connection and replaced nut. Reverse it for assembly. 3 minutes tops $6 later it is done. Easy money saved by a DIY.

used pliers to hook up spring according to repair video.5 mins to check for proper tension.

The first sensible thing to do is to find the circuit breaker for your dishwasher and switch it off so as not to short anything (or yourself) out. Next, remove the lower piece of metal bracket from beneath the door by unfastening the two sheet metal screws (a nut driver or a screwdriver will do the job), taking note as to how it comes off so as to facilitate replacement. Some will recommend loosening the screws at the top from beneath the counter and pulling the machine forward a bit to gain access to the sides but, if you have a small enough hand (as I do), you can just reach in there and and hook the spring into place. I didn't want to risk loosening any plumbing! You'll need a flashlight to see where the ends connect. And, if one spring is still intact, you can reference that to reassure yourself you've got it right. I was able to stretch the spring out by hand and hook the thing to that little plastic gadget that pivots when you open the door. That's it! Button her up! You're done!

Take out the old arm, and snap in the new one.

Eventually broke off old heating element to get it out

put new arm in place on bracket. Perfect fit.

There were 4 zip ties holding old silverware basket on to bottom rack snip them, remove basket install new basket with zip ties both ends 2 more in middle about 1-2” apart. Try to install ties about 1/2 way up on basket so it doesn’t get top heavy.

After getting a totally incorrect length of hose from partselect.com . Went to local hardware store and bought hose for $3.00 vs $20.99 + $10 shipping!
Partselect sent replacement hose of 24 1/4” vs the original hose of 27”. Good luck getting any response from them once they have your money!

New piece snapped right on

The old part easily snapped off and the new part was snapped into place. No tools were needed. Very easy. Saved quite a bit by doing it myself instead of calling a repairman.

Removed the cover at the front bottom to gain access to the nuts holding on the element.
Turned off dishwasher breaker.
Removed the wires connected to the element.
With a 1/2" wrench, removed the element mounting screws.
Removed the bottom rack.
Removed the lower spray arm.
Removed the element from 2 clips.
Removed the element.
Put the new element in place.
Clipped it in.
Put new screws on and tightened up with a wrench. Not too much but enough to squash the washers to make a tight seal.
Replaced wires.
Replaced spray arm and bottom rack.
Turned on the breaker.
Ran it through a cycle to check for leaks.
Replaced bottom cover.