All Installation Instructions for Frigidaire Refrigerator FRFN2823AS3

Wrong Part sent!!!!!

I did not do a repair. You sent the wrong part & I didn't open the package but I can't get hold of anyone to return the part and get the correct part.

I am very upset that no one will help me. I paid $ 37.28 for the part I ordered and then the wrong part was sent

The sku # on the package is 242010901.This is a roller type part and I ordered a small wheel.
I can't even find a return address to send it to.. Please help me
Elizabeth Romage
libbieinrichmond@comcast.net
8042627963

Parts Used:

ROLLER Assembly

ELIZABETH from HENRICO, VA
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Thin, flexible edge on outermost door gasket was tearing from the main gasket, likely due to being rubbed when accessing refrigerator..

Gasket is held in place by an extrusion on the back side. Simply remove the old gasket and press the new gasket's extrusion into the track on the door.

Parts Used:

GASKET-DR,MAGNETIC FF WH 36

Dennis from Oley, PA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Replace Water filter Frigidaire Refrigerator

Followed the simple instructions on the device and in the appliance use and care manual

Parts Used:

Filter

Thomas from ROCKINGHAM, VA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

7 of 18 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Torn Freezer Drawer Gasket

Remove the freezer drawer by unscrewing the two 12mm screws on both sides of the drawer.
Lift the drawer up out of the slots the frame and away.
Lay the drawer on a padded surface to protect the drawer cover finish.
Pull the old gasket out of the drawer and discard.
Position the new gasket around the edge of the drawer. Starting at one corner press the gasket into the slot in the drawer edge. Continue working the gasket until you return to the starting point.
Inspect the gasket to ensure it is seated in the slot completely.
Return the drawer to the refrigerator, placing the lugs on the drawer into the slots of the frame and insert the screws to their original position and tighten securely.
Inspect the drawer for proper level/sealing in the freezer drawer position. Adjust as necessary.

Parts Used:

GASKET,FREEZER DRAWER,GREY

Billy from FAYETTEVILLE, NC
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Socket set

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

1 Broken plastic mullion hinge. Mullion was not operating correctly.

Removed screw on Mullion so that the replacement hinge can slide onto the small plastic bracket on the door. Slid the mullion on the hinges and screwed in muliion (1 screw).

Parts Used:

Upper Or Lower Mullion Hinge Pin

Bernard from NEW WINDSOR, NY
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

2 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Previous seal had a tear and cold air was leaking around seal

Pulled the old seal out of the groove. Placed new seal in the groove. New seal has to be heated and massaged to get it into proper form so it does not leak. I have been continuously heating and massaging to get the seal to get it in the proper form. Been working on it for a week. Almost there.

Parts Used:

GASKET,FREEZER DRAWER,GREY

Daniel from Hampton, NH
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

GASKET WORN AND LEAKING

SIMPLY REMOVE THE OLD GASKET PULLING LIGHTLY BY HAND
THEN PUSHING THE NEW GASKET BY HAND

Parts Used:

GASKET-DR,MAGNETIC FF WH 36

Dennis from Lancaster, SC
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

A set scew was ordered twice.

The first order arrived in a huge box and there was no scew to be found, the box had wholes in it. I was given a refund and told to order again.

The repair did not happen and the set screw which was actually recieved the second time was returned because it was the wrong size.

Parts Used:

Screw

Susan from BRAINTREE, VT
Difficulty Level:
Very Difficult
Total Repair Time:
1- 2 hours

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

THE GASKET LOCKING INSERT DID NOT FIT THE BOTTOM OF THE DOOR.

I REMOVED THE OLD GASKET BEING VERY CAREFUL TO SEE EXACTLY HOW IT CAME OFF. I INSERTED THE LOCKING INSERT INTO THE TRACK IN THE DOOR WHICH DID NOT FIT AS THE OLD ONE DID. AFTER USING TREMENDOUS FORCE WITH MULTIPLE TOOLS I DID MANAGE TO GET THE TOP AND THE SIDES TO LOCK INTO PLACE AND EVENTUALLY HOLD. THE BOTTOM OF THE GASKET DID NOT HOLD SO I USED CLEAR CAULK AND TAPE TO HOLD THE GASKET IN UNTIL THE CAULK CURED. AFTER THE CAULK CURED THE GASKET HAS, SO FAR, REMAINED TIGHT.

Parts Used:

GASKET,FREEZER DRAWER,GREY

Robert from Lexington, SC
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

No problems

I had no problems. Screws arrived sooner than expected. It was a very simple installation. Very pleased with both the product and service.

Parts Used:

Screw

Nancy from LEHIGH ACRES, FL
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Wrench (Adjustable)

2 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

From day one the installer did not tighten the screw in the freezer handle. It finally came apart. They didn't leave me the Allen wrench for my fridge.

Simple tightening of the screw with the right tool.

Parts Used: