HTW200ASK1WW Hotpoint Washer - Instructions

Took 4 screws out of back of control panel. Tested old capacitor. Installed new one. Put back on tested spin cycle everything is doing great

First, I made sure the washer was empty of cloths and water and then unplugged the appliance. I laid a towel down on the floor just in case there was any water remaining in the drum and I slowly laid the washer on its side, I was able to do this with the drain and water hoses still connected to the washer, be careful you do not rip any of these connections or simply disconnect, to each is own. Once I had the washer on its side, I used the socket wrench to remove the 3 bolts holding the belt drive cover on the motor. I placed the cover and bolts to the side, and I began pulling off the old belt that had slipped, stretched, wrapped and ultimately hung up the motor off buy unwrapping it from the motor itself. Once the motor was free from the belt, the wheel was able to spin like it is supposed to. I installed the new belt by simply wrapping it on the motor wheel and spinning it on to grab onto the second wheel, just make sure to line the belt up correctly so it does not fall off. I placed the cover back over the belt and bolted on the 3 bolts. I flipped my washer back up and ran a small wash cycle to make sure that the belt was working properly and once it began to wash, I threw in some cloths and began washing as normal. The whole process took less than 15 minutes.

The drain pump had three screws. Frist unplug the machine and turn the water off. And unplug the hose for the Hot and Clod Water. Make sure their no water in the tub. Unplug the pipe from the Tub. The unscrew the nut for the connector. Then unplug the connector and be careful not to damage plug for the connector. Press the plug connector with your finger or long nose pliers . Then just hook the new plumb and you all set.

Disconnect water lines.
Remove top control panel.
Remove 2 screws & disconnect wires & replace old for new

Unplug machine
Move machine out from wall
Removed 4 screws on back plate
Removed the 2 screws holding the assembly to washer
Pulled old unit out and reversed process to put back together

But when I went to test it would not drain tipped washer up and removed hose from motor and found a sock inside
Remove sock and washer runs great.

Just a note this website was very helpful in finding the right part with the exploded view of parts

Thank you

I watched a video on a few times that PartSelect sent me about how to make the switch from the broken lock set to the new one. And it really went just as the video showed. So far things are working.

Unplugged the washer, turned off water supply to washer, using channel lock pliers disconnected hoses to valve assembly, using nut driver removed two screws on back of console, pulled console away from top exposing valve, disconnected wire harness from valve assembly, using nut driver removed two screws holding valve assembly in place, removed defective valve assembly, transferred foam spacer from defective valve assembly to new valve assembly and installed new valve in opposite order of removal.

Once I determined it was the drain pump, (by taking off the drain hose and letting it empty by gravity, then running the spin cycle which worked ok) I ordered the part, got confirmation from PartSelect.com that it would fit my washer. I removed the old pump taking out the 6 screws needed to hold it and the cover in place and unplugged the electric connector. I installed the new pump from PartSelect.com using the same cover and 6 screws and electric connector. I reconnected the drain hose and the washer has worked perfectly since then!

Put the parts in, turned washer on.....lid lock still blinks, will not operate. Suggest the control board that sends the signal to the solenoid lid lock switch is defective. Buying a new washer, scrapping this one.

Unpluged the washer first got as much water out of the drum as possible the leaned the washer over forward and let it rest against something removed hose clamp from pump side and removed the drain hose from pump remove plastic cover and unplug pump push tab and pull remove bolts from pump remove pump install all components in reverse be sure to replace pump to drum seal as well

Unplugged the machine, pulled it away from the wall, didn’t have to disconnect water lines, set the parts out on the counter as I went over the instructions a couple of times, followed the directions, plugged it back in, worked perfectly again.

any electrical device unplug the power cord. I followed the instructions the best I could understand them. but once the part was removed I took pics from my cell phone of how the wiring ran, and also what other connections I had to undo. all connections were made, connected the hot n cold hoses, plugged into the washer no beeps or sounds as before opened the hot n cold water valves, and the tub was being filled with water. could not turn on the washer, no lights or beeps... so I gave up I spent too much time on this machine and money too, hope to get an RMA for the Lid Switch assembly

I replaced the Pump Drain assembly. It was very easy. Removed 3 bolts and disconnected the electrical wire harness and put new one on. It works great.

Look it up on YouTube to see how to repair the problem. Unscrewed the necessary screws. Took apart the top, pop open the loader replace the bezel. Put everything back together again. Was simple.

Unplug the cord and shut off hot and cold water faucets.

headache avoidance: The male threads of the inlet valve are plastic. Gently turn the female hose ends onto them at the kitchen table with the eventual position in mind then tighten.

1. Remove 4 screws holding shiny metal backplate w/ 1/4" socket (easy)
2. Pry tabs loose, top of plate (easy).
3. Pull electric leads from 2 solenoids (easy).
4. Remove 2 long screws holding upper painted structure (easy).
5. Remove 2 screws holding valve in place (easy).
6. Tilt and slide the valve loose and pull it out (easy).
7. Replace valve and reverse steps 6-1.

n.b. no inside water tubes; water drips straight into tub

Also, an hour should be enough. I spent more time than needed guessing, dealing with a few issues, opening the machine again, starting over, etc.

ps. I guessed at the age.