All Installation Instructions for Hotpoint Washer HTW200ASK1WW

Washer would not advance to Wash

Lift the cover, undo too screws, Slide out broken part, slide in new part put in the screws and close the lid.A piece of cake.

Thank you for the super fast service on Christmas eve no less!

Parts Used:

LID LOCK SERVICE KIT

Garry W. from TAMPA, FL
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Washer shaking all over the place.

Took top of the washer then took one rod off at a time and replace with the new one, the back two are a little bit harder to do but it works great now.

Parts Used:

WASHING MACHINE ROD & SPRING-LEFT-BLUE

ROD & SPRING Assembly RIGHT - RED

CHUCK from ZOLFO SPRINGS, FL
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Strong noise when spin, the washer "walk"

>Change 4 rod & spring, (2 red, 2 blue) and
>LEVEL THE WASHER
(this was the initial cause of the failure!)
>clean tub

Parts Used:

WASHING MACHINE ROD & SPRING-LEFT-BLUE

ROD & SPRING Assembly RIGHT - RED

Luis from San Luis, AZ
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

The machine stopped working completely! My wife went on YouTube,and learned that it could be the motherboard or the door latch. We changed both, and the washer would only fill but did not drain, and spin! We called a serviceman, and he had to program the service board,but said that the new door mech

We changed the circuit board once, and the door latch mechanism twice because we ordered a faulty part. Then we had to hire a service man to program the circuit board, and to inform us that the door latch mechanism was faulty.

Parts Used:

LID LOCK SERVICE KIT

Scotty from OCEAN SPRINGS, MS
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Lid was forced open and broke latch

Follow the super simple, precise instructions and it is very easy. Only harder part was unclipping the front of the lid.

Parts Used:

LID LOCK SERVICE KIT

Chris from LARGO, FL
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Washer not spinning out completely.

1) Unplug washer
2) Remove water supply hoses
3) Remove drain hose
4) Tilt washer forward
5) Remove 4 bolts covering the motor assembly to access belt.
6) Remove old belt by turning it off the pullies.
7) The new belt needed to be stretched by attaching one end of the belt to one of the pullies using a zip tie. I did this by drilling a small hole in the larger pulley, large enough to allow the zip tie to pass through.
8) After tightening the zip tie to the belt, slowly turn the larger pulley to stretch the belt on to the smaller pulley.
9) Make sure belt is properly seated on both pullies.
10) Reinstall the cover.
11) Reattach drain hose and supply hoses.
12) Plug washer back in.

Parts Used:

Washer Drive Belt

Jeremy from JOHNSTOWN, NY
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Socket set

2 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Water dripping after washing was done

Watch a YouTube video on how to fix it. Video was really easy to follow

Parts Used:

Water Inlet Valve Assembly

Kevin from MANCHESTER, PA
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers, Socket set

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Washer wouldn’t drain

Remove old pump install new one. Three bolts and an electrical connection

Parts Used:

Drain Pump

Ronald from Chickasha, OK
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

washed well but would not shift out of spin cycle

easiest repair I have ever made. No problems and was surprised as to how fast and easy it was to repair. I did not need two of steps the instructions stated I had to do. best purchase I have ever made.

Parts Used:

MODE SHIFTER

terry from MILLINGTON, TN
Difficulty Level:
Very Easy
Total Repair Time:
30 - 60 mins
Tools:
Socket set

2 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Out of balance often

After loosening top screws on back ,snaps in front,no need to total remove top changing springs you have to reach below top of case with vice gripes and attach to spring rod about 8 inch down and lift up (tuff for 80 year old) tap down on plastic retainer, turn retainer 1/2 turn so hook will slip out ,now lower spring it will fall out of bottom retainer. Now for reinstall ,instead of vice gripes on the spring down inside case with no room , by hand take new (correct color) spring reach deep inside and install bottom into bottom retainer now take old spring run long end hook threw retainer hole in top case, hook to hook ,now you can pull new spring easy out the top about 3 inches and now vice gripes above case with enough room to reinstall top retainer remove gripes now only 3 more to go

Parts Used:

WASHING MACHINE ROD & SPRING-LEFT-BLUE

ROD & SPRING Assembly RIGHT - RED