KDTE104ESS4 KitchenAid Dishwasher - Instructions

Replaced upper rack adjuster on both sides as these adjusters seem brittle due to heated drying over years. Followed YouTube video for repair. Very easy to fix.

Replaced the detergent dispenser on the door. Followed YouTube video with slight modification given moderate difference in model on video and my model. Relatively easy repair that takes a little bit of time.

Very easy to twist off the old pump and replace with new part. Worked perfect after replacement! We just followed you tube instructions

unplug, disconnect water, remove all screws holding the machine in the cabinet. slide out the machine to access the 4 bolts hold the rail. Have a prop to hold basket in place as you remove old rail> Plastic clips front and back, hold the basket to the rail. Be careful not to break, not include with the replacement rail. If you are not handy with tools and no insight...hire it done

My husband did the repair. It was very easy. He basically just popped off the old wheels and popped on the new ones.

Removed broken tin row. Replaced with new tine row. Tokk less than 1 minute.

I took the valve off and actually hooked 110 volts to the vale and tried to blow through it and it would not let air pass through it. I replaced the the new valve in about 15 minutes and it works fine

Ordering the part was very easy. It shipped fast and delivered over 3 days. It fit perfectly

pulled the dishwasher out (took the most time-1 hour) and 30 min. to install new door balance kit and springs. Replace both sides while the unit was out.

In looking at the parts catalog the part I needed didn’t state left or right side piece. I understood that the same part was used on both sides. Knowing the other side may fail also I ordered (2) pieces. Once they arrived I took apart the surrounding element using a screw driver to pop the enclosure apart carefully. I noted where each clip went and re-assembled the enclosure.

Initial inspection of the issue and research suggested the door latch was malfunctioning / broken. I bought the part and expressed it home. The installation involved removing the door screws on the inside of the door, separating the front and back panels, unplugging the door latch, removing it from its niche and popping in the new one. Reverse the take apart and it was done. Very simple swap. Hardest part was juggling the two halves of the door and preventing the door for trying to close in the process as the bulk of the weight is in the outside half of the door.

The new part did not fix the issue. The door strike was the next part that could be broken / malfunctioning. I ordered that part as well and replaced it. In the process of replacing it I found that the original door strike had been installed upside down. I am guessing it was installed at just the right pitch, or maybe even bent at the manufacturing facility, so that it latched. No idea how it managed two years like that. I installed the new one correctly and the door latches perfectly. Both parts I removed from the unit I will retain if my new parts should fail in the future.

1. Remove front of door with torx screws around inside top and sides of door.
2. Unclip and remove plug with two wires for dish soap solenoid. You may have to lie on your back or use a mirror to see the location of the small clip retaining the plug.
3. Unclip and remove dispenser module. Here's the rub: the clips used to retain the unit in the door panel of my dishwasher are tabs cut in the stainless steel cut-out and rolled back at a 90 degree angle to retain their springiness. They seat against the back edge of three plastic ridges along the top, bottom and one along each side of the dispenser module. The key is to remove the module without permanently bending these tabs, thereby losing their springiness and destroying their ability to clip tight against the new module to hold it in. I had some success slipping 3 pieces of flashing under the stainless tabs along the top and sides of the old module, allowing the plastic retaining ridges to ride under the tabs all together and move forward to disengage the clips without permanently bending the tabs.
4. Reassembly is just the reverse.

Was easy to do but would recommend getting the 4 bolts that hold both racks in. The ones on the left side had rusted and hard to remove and reuse

Removed the inner panel, remove electrical connection to dispenser, remove dispenser, metal tabs that hold it in, are a bit hard to pry metal tabs, and when installing net dispenser tabs are also a little difficult to pry tabs to install but doable. So far works like it should.

Gently pull the old door seal out of it's track observing the orientation of the seal and the amount of extra seal at the ends of the seal grove/track..
Start installing the seal on one side leaving about the same amount of extra seal as original seal before removal.
Be sure the seals orientation is the same as the seal that was removed.
Carefully pressing the seal into the grove/track designed to hold the seal. Be careful to fully seat the seal into the grove/track.
The corners will be a little tricky, but carefully press and seat the new door seal all the way around. There should be a little extra seal after you get to the end of the grove/track.
Good luck, the new door seal solved my water leak.

Took off the old wheels and placed them on the new rack - fast and easy if you watch the video.