L3B325GL0 Range - Instructions

Instead of flipping circuit breaker, we pulled the oven away from the wall and unplugged it. Used socket wrench to loosen screws of bracket holding old element onto the back oven wall, then gently pulled element until connecting wires appeared. Removed the 'clips' attached to the old element prongs and discarded old element. Reattached the 'clips' to new element prongs, then gently pushed prongs into back into oven wall until the bracket was flush with the wall. Used socket wrench to screw and tighten the bracket into place. Plugged in the oven and tested the new element to make sure it worked. The whole process took only a few minutes.....it took longer to clean the oven before installing the new element.

The repair went surprisingly well! My only problem was the bottom screws needed WD40 to loosen, but otherwise the parts went in easily.

Removed oven racks and took the opportunity to clean my oven. Then removed the two hex head nuts holding the burner assembly in place. I slid out the burner (very slowly) hoping the connectors were intact and that there was enough lead wire to make for an easy repair. Yes... there were 2 inches of lead wire. It took a couple of minutes to swap out the parts and... success!
Don't forget to turn off the circuit breaker before starting repairs.

I turned off the main power! Then unscrewed the back cover unhooked the wires and unscrewed the coil inside of the oven and pulled it out. My 10yr old son and I measured it and went online to order the part. I first did go into BestBuy and they didn't have the part (But they tried to sale me a new oven!) LOL Now who said a newly divorced mom couldn't fix her own oven! My Tech Support skills came in handy! Women Rock! LOL

Removed two screws and removed the oven elelent. One wire was not through the back of the stove. Ordered new element anyway. Slid stove out (slide-in model). Unplugged power. Removed two covers protecting wires on back of stove. Found wire for oven element. Had to cut and strip end of wire and use new blade clip. Crimped new clip to wire and inserted into oven through back of stove. Replaced covers. Plugged oven element to wires and tried out oven. WORKED ! Saved new oven element for next time. Difficulty encounted was lack of knowledge on where stove was screwed into counter-top and what size blade clip to buy. It always helps to have a dog 3" away just itching to lend a paw.

first open oven door a couple inches and slide door up off hinges, then removed storage drawer to gain access to hinge spring, remove hinge spring with pliers noting which hole spring was attached in.then remove three screws from hinge and installed new hinge put three screws in attached spring back and put storage drawer in and oven door back on.

It was surprisingly simple. All I had to do was shut the breaker off to the stove(safety first). Next open the oven door and use a flashlight just to help you see,and unscrew the two screws holding the element in place on the back stove wall. Next slide the stove away from the was to give yourself enough room to access the back of it(you may need to unplug it to get it out far enough. My model had a cover over the back that took six easy to remove screws. Once the back cover was off I could easily see where the element was plugged into, so i removed the wires from the end of the element(just female terminals slipped over the end) i then went back to the front of the stove and pulled to element out.

To install the new one...just guide the two ends throgh the back of the stove...install the two screws to hold it in place...go to back of stove..plug in wires(they were diff sizes so you couldnt mess it up) and put the cover back on..plug in oven..slide it back..and try it out...its that simple

Lifted door off the front of stove, real easy, but heavy, took out old hinge, and replaced with new hinge, I just looked where everything was before, I replaced with new, replaced door back on, and I was finished.

Flipped off the circuit breaker first. Unscrewed the two screws holding the element in place. Pulled out about 4-5 inches. Tried several times to pull apart the connections, finally got 'em - don't give up (I must have weak fingers). Then plugged in the new element, shoved the wires back in, screwed it back in place, flipped circuit breaker back on, turned the oven on.... made brownies (o:

Of course, power off first, then I removed the old one and inserted the new one, make sure everything in right place, then turn on power, simple as 1-2-3.

Parts Select is the only parts place I found on the internet that had what I needed on my first purchase, so when I needed these clips I naturally went back to them. Product was easy to find, price was fine, receipt for payment quick and more importantly receipt of item was super quick. Thanks to the efficiency of this place and my old appliances, I will continue to go to them as needed.

Pull out oven and unplug from 220 outlet. Remove rear upper/lower cover (4 screws), Remove two wires from rear of element. From front, open oven door, remove two screws and pull out old element.
Install new element by reversing above sequence. Then test and push oven back in place. Easy!

removed oven door, removed drawer under oven, removed three screws holding hinge assembly, unhooked spring from hinge arm, inserted new hinge arm, attached spring, positioned hinge assembly and replaced screws, reinstalled drawer beneath oven being certain that no pot handles interfere with the hinge spring loaded arm, reinstall oven door.

I tapped the screwdriver with a hammer lightly on each of three screws to loosen them. I checked to see the position of the spring on the hinge. I then removed the hinge, put on the new hinge and placed the spring in the exact same position. The door works very good. The hinge replacement was a no-brainer.

first i removed the two screws that hold the element in place. then pulled the element out about 3 inches and disconnected the two wires .then i connected the two wires and pushed thebake element back and replaced the two screws.then i put the circuit braker back on and tested the stove and it worked great. very easy to do.