LFHD2251TF4 Frigidaire Refrigerator - Instructions

Remove filter by twisting counter clockwise

Install bypass by twisting clockwise

1. I took out one screw on the ice maker and loosened the other two screws and unplugged and removed the ice maker.
2. Next I took out 2 screws from the bottom of the auger drive box and unplugged the wiring harness and removed the box. The wiring harness was a little tricky. The lock on the plug pushes in to unlock even though it looks like it pulls out,.
3.next you must remove 2 screws from the left side bracket that holds the auger box and remove the bracket.
4.Now take out 8 screws that hold the back panel in place and remove the back panel.
5. now your looking at the evaporator fan blade and motor. The simple way to replace the fan blade is to unplug the motor and remove it from the freezer. It just sits in with nothing holding it. The fan requires a little pressure but should pull right off. Install new fan blade and put everything back in the same order it was removed.

Replace gasket

Once I found out how the roller was part of the shelf and not the rail I replaced the broken shelf

From discussions with friends, I determined the problem might be easy to fix. The fridge made a lot of noise, but the compressor DID come on, and inside the freezer was cold, but the main fridge was warming.

After unplugging the fridge, I removed the fan assembly in the freezer (there were about 4 nuts and a couple of plugs to uncouple.

I could see right away the fan blades has broken off, but the motor looked good. The new new fan pushed easily onto the shift and fit perfectly in the housing.

I reinstalled the fan assembly, plugged in the fridge, and right away heard the new fan come on - very quietly. What was a roar became a whisper and the fridge was down to 38 degrees with a few hours.

Basically the only tool you need is a screwdriver to remove two screws on the trim piece and then the screws on the dispenser unit. This is where the patience comes in. Don't force anything or you'll be buying a new unit again. The tolerances are very close and the tubing for the water needs to be removed from the brackets carefully. Pay attention where the wire connectors go since you'll need to plug in the new ones. From there, just put things back in reverse order and close it up. I'm fairly good with tools and figuring out how to repair things, but I gotta tell you, this is really easy. Don't be afraid.

i put casket on i notice when i received casket in shipping box was bent on the end of the casket 's did not solve problem casket not flush air is due to damage from shipping in the box not happy with the product.

I screwed the old wheels that came off on to the new part. It took less then 10 minutes.

Located problem part of ice maker on web site. Picked the part that had the highest percentage of being the the part that was broken (58% I think). Removed the part, waited for the new part, then put it all back together. Simple. It works great. Thanks for having such an easy web site to diagnose the problem.

Unscrew a few screws and remove some plastic covers to access the ice cube tray. Undue two wire connections and remove the tray. Put in the new unit in reverse order. I heard it may take awhile for the new ice maker to start doing anything. Mine didn't do anything for 6 hours, then made it's first batch. Making ice fine now ever since.

Remove old gasket by pulling it away from the frame. Work all the way around the gasket till it is entirely separate from the door. Remove the old gasket by slipping it over the door. Note the orientation of the new gasket will have the small bead towards the door - slip the new gasket over the door so that it is in the inside of the freezer door. Press the small bead into the slot in the door. Work all the way around, pressing the bead in with your fingers. When it's all secure, close the door and check for no gaps. Takes 5 minutes and no tools - very easy. Make sure you order the correct COLOR of gasket - it comes in black and white. The black looks best on stainless steel door.

The diagram on the frigidaire website said 4 screws and 3 wires to disconnect and part comes out and reverse the steps for install actually took less then 5 mins...easiest and first repair I have done and the part was 20 bucks cheaper at parts select then anywhere else on the internet!

Unscrewed the 4 screws that hold the dispenser in place. Disconnected the wiring harness from the old dispenser.

Reconnected the wiring harness to the new dispenser.
screwed in the 4 screws that were removed.

Works like a charm!

At first I thought it was the support from the diagram. Not easy to get a visual 3d LIKE OTHER WEBSITES have. Current diagram looked like all I needed was the Bin. then found out I needed the cover which was an extra 100.00.

I was not happy. Theres nothing to tell you how to replace 24b part per diagram on website. You have to remove both left and roght shelves connected together and then unscrew, replace, etc,. Again no instructions on how to replace such said item.

Because of this I rate very low.

Removed the trough that catches the ice.. two philips screws to take the front cover off. Side and bottom. Than quarter inch to remove cover over wires. Unplug ones to ice maker. Slide out a little and down. May be a zip tie in the back cut with sheet rock knife. Reverse to install.