removed dryer door 4 screws removed front panel removed front tumbler bracket removed blower cover removed wires attached to heat and door sensors removed top removed drum and belt removed side panel removed clamp holding idler pulley replaced pulley and clamp reversed above steps
First I put the square female end iof the door catch kit nto the square hole as snug as I could. Then I gently pushed the door against the piece until I heard it click in to place. That's it!! Sooooo simple--
Took off the four screws to get to the female clip and used pliers to squeeze it out. Next was using pliers to pinch out the male connector and place the new one in.
1 - unscrewed door 2 - made a mess because the directions did not work for my dryer 3 - figured it out = eventually 4 - popped loose the front panel 5 - unscrewed metal bars (that were holding the top down in the front) 6 - lift front like a hood on a car 7 - unscrew the rest of the front until the drum was loose and I could get to the felt strip 8 - glue new strip on where the old strip was = to the front and back plates that hold the drum 9 - put it back together :)
Blower wheel had broken fins, motor bearings loose
This was fun! Kill the power! Remove door, remove from panel, remove front drum support, remove drum and belt, remove blower cover, remove blower wheel, remove electrical connector from motor, take two clips off motor mount to remove motor. Put it all back in with new parts. 200 bucks and back in business. Go for it. Bob
Using the pictoral parts diagrams on the PartSelect website, it was a logical process to disassemble the dryer to change the drum drive belt. This was a great opportunity to clean lint from the motor and air passages and inspect all components. Cleaned the belt track, the roller drum wheels and felt seals. Unit now runs like new. BTW - very fast shipping on the replacement belt and it was the right part the first time!
Okay, first of all, just let me say, if I can do this, ANYONE can. I am not very handy when it comes to things like this. I watched online videos and they will walk you through everything. I am so pleased with the results. Quiet as can be now. Before, we would have to shut the door when it was on because the scretching was so loud! The parts on this site were far more affordable than at my local repair store and they all came right to my doorstep. Overall it took me about 45 minutes and three beers :) Good luck!
Dryer making grinding noise, and spotting clothes with black dust.
Followed your video; replaced felt seal on front of drum, (torn in two or three places), and replaced both front guide kits,which were ground to the metal, causing the black dust, ( metal shavings). Thanks for the help, Buck. The drum support rollers were OK.
The repair was very simple.I removed the door and the front cover.Right in front of the blower housing sat the temperature control thermistor.All that was needed to do the swap was a nut driver.Everything I read said the high limit thermostat may of been bad but it was fine.Ordering the parts was easy and fast all I needed was the model number and all the charts and numbers were easy to find.Thank you Parts select..
popped up top of dryer -- With pliers squeezed clips on inside of latch - - with screw driver pryed latch out -- just pused new latch in.......... Thanks to parts select for sending part sooo fast.. wife was happy.. Thanks, Dale
Removed door and front and drum. Removed fan assembly. Be careful when working fan off of motor shaft. Unhooked wiring from motor. Removed clips. Replaced motor. Reverse procedure to put dryer back together. Now works like new. Very, very, happy. Part came in 2 days using standard shipping. Way better than buying a new dryer.
the dyer would not start, just show an era code"88"
This problem was the result of a lighting strike that actaully happened a year ago. The dryer still worked but there was a special routine to get it to start. It finally would not start at all and i assumed and ordered the control unit and it arrived the next day. It took just about five minutes to install, just remove to the old board and disconnect the plug-ins and tighten a few screws, much easier and less expensive than calling a service technician