Part Location Diagram of WP74007961 Whirlpool Orifice Holder with Spark Igniter - 9.2K
See part 8 in the diagram
( Grid squares measure 1x1 inch )
Customer Service Representative

Get in touch, we're here to help!

Monday to Saturday
8am - 9pm EST

customerservice@partselect.com

Orifice Holder with Spark Igniter - 9.2K WP74007961

Rated by 2 customers 

Easy 

More than 2 hours 

Ratings submitted by customers like you who bought this part.

$ 75.81
  In Stock
Get FREE EconoShip on orders over $100! T&C apply

Get this part fast! Average delivery time for in-stock parts via standard shipping: 1.8 days.

Does this part fit my model?

Need help finding your model number?
PartSelect Number PS11744213
Manufacturer Part Number WP74007961
Manufactured by Whirlpool for Maytag, Jenn-Air, Kenmore, Whirlpool
Product Description

Orifice Holder with Spark Igniter - 9.2K Specifications

Mounting screws are sold separately.
How Buying OEM Parts Can Save You Time and Money

How Buying OEM Parts Can Save You Time and Money

Troubleshooting
This part works with the following products:
Range.
Part# WP74007961 replaces these:
AP6011022, 74007391, 74007961, 7527P022-60
Back to Top
Customer Repair Stories
 Average Repair Rating: 2.3 / 5.0, 2 reviews. What's this?
Sort by:
  • 1
Sorry, we couldn't find any existing installation instruction that matched.
oil overflowed and destroyed the insulation
I removed the top pulled out oil soaked insulation then decided to clean some of the parts Broke a torx screw on the burner then striped the tube and the burner so had to order the new parts and then put everything back together and it works fine again..It was my fault and the stove has not given me any problems..
Other Parts Used:
Top Burner Tubing - Right Side Orifice Holder with Spark Igniter - 9.2K Torx Screw
  • Ray from Grand Rapids, MN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Screw drivers, Wrench set
2 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Ignitor switches shorted out
The ignitor switches are installed on top of the 4 gas valves for the range top. These switches control the electronic ignition. To replace the switch assembly the top of the range must be removed to gain access.

This was made more difficult by the fact that the screws that hold the burners to the range top were rusted and had to be drilled out so the the burners could be released from the top.

1. Disconnect the power to the range.
2. Open the top oven door.
3. Remove 2 - 1/4" sheet metal screws at the front corners of the range top assy. Remove the Burner knobs and the two Phillps screws that holds the gas valve assembly to the range top.
4. With a drill, remove the tops of the screws to release the burners from the range top. If the screws are in good condition and just unscrew them and the upper burners from the Orifice Holders. (I had to replace the orifice holders because the screws were stuck in them due to rust).
5. When the burners are free, lift the range top at the front and remove it from the range. Disconnect the ignitor wires from the ignitors on each holder.
6. To replace the Orifice Holders, disconnect the gas supply pipes from each holder by loosening the compression nut at the holder using an adjustable wrench. Secure the Orifice Holders when loosening the fittings, BE CAREFUL not to damage the aluminum gas supply pipes.
7. Note that there are 3 different Holders, be sure to use the holder that matches the specific location.
8. For LP gas fueled ranges ONLY, remove the small gas jets from the old holders and install them in place of the parts supplied with the new orifice holders. The new parts contain NATURAL GAS jets which are not compatible with LP gas. Each Different Orifice Holder uses a specific orifice or jet, make certain that the orifice matches the orifice holder. Check for leaks at the gas connections using soapy water.
9. Carefully raise the old ignitor switches (4) off the shafts of the gas valves. Note the top and bottom configuration of the switches
10. Carefully release the wires that come from the rear of the range from the rearmost switch. Press a suitable pin or other suitable tool in a the hole, beside the wire, just enough to release the wire. (Look at the NEW switch assemble to see how this works). Remove the wires from the NEW switch first to see how it is done. Repeat the process on the old switches. (you will re-use the wires that come up from the rear of the range.
11. Install the new switch assembly over the four (4) burner gas valves, take care to align the "D" shaped shafts with the holes in each valve.
12. Insert the wires in the two connections on the rearmost switch. CAUTION!!! Be sure to install the wires so that the color codes agree with the wires on the new switch assembly. Black to black and gray to gray.
13. Install the 4 clear plastic "shields" over the shafts and against the top of each switch.
14. Re-connect the ignitor wires to the burners and Re-Install the range top, in the reverse order of dis-assembly.
Other Parts Used:
Orifice Holder with Spark Igniter - 16K Orifice Holder with Spark Igniter - 5K Spark Igniter Switches and Harness Assembly Orifice Holder with Spark Igniter - 9.2K Torx Screw
  • Michael from Dardanelle, AR
  • Difficulty Level:
    Difficult
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
39 of 46 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • 1
Questions and Answers

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

1 question answered by our experts.
Sort by:
  • 1
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Gary
September 17, 2017
What screws do I need for the orifice holder?
For model number MGR6775ADW
PartSelect logo
Hi Gary, Thank you for the question. The mounting screws for the Orifice Holders are PartSelect Number PS11741257. Hope this helps!

Was this helpful?
Thank you for voting!
Related Parts:
  • 1
You May Also Need ?
Model Cross Reference
This part works with the following models:
PartSelect Number: PS11744213
Manufacturer Part Number: WP74007961
Brand
Model Number
Description
Kenmore
66578002700
Range
Kenmore
66578002800
Range
Kenmore
66578002801
Range
Kenmore
66578002802
Range
Kenmore
66578002803
Range
Kenmore
66578003700
Range
Kenmore
66578003800
Range
Kenmore
66578003801
Range
Kenmore
66578003802
Range
Kenmore
66578003803
Range
Kenmore
66578003804
Range
Kenmore
66578009700
Range
Kenmore
66578009800
Range
Kenmore
66578009801
Range
Kenmore
66578009802
Range
Kenmore
66578009803
Range
Kenmore
66578009804
Range
Jenn-Air
JDR8895AAB
Range
Jenn-Air
JDR8895AAS
Range
Jenn-Air
JDR8895AAW
Range
Jenn-Air
JDR8895ACB
Range
Jenn-Air
JDR8895ACS
Range
Jenn-Air
JDR8895ACW
Range
Jenn-Air
JDR8895BAB13
Range - 30" DUEL FUEL RANGE
Jenn-Air
JDR8895BAS13
Range - 30" DUEL FUEL RANGE
Jenn-Air
JDR8895BAW13
Range - 30" DUEL FUEL RANGE
Jenn-Air
JDR8895BCB13
Range - 30" DUEL FUEL RANGE
Jenn-Air
JDR8895BCS13
Range - 30" DUEL FUEL RANGE
Jenn-Air
JDR8895BCW13
Range - 30" DUEL FUEL RANGE
Jenn-Air
JGR8890ADP
Range
Customer Service Representative

Get in touch, we're here to help!

Monday to Saturday
8am - 9pm EST

Contact Customer Service