Orifice Holder with Spark Igniter - 16K Specifications
16K.
How Buying OEM Parts Can Save You Time and Money
Troubleshooting
This part works with the following products:
Range.
Part# WP7527P021-60 replaces these:
74007390, 74007962, 7527P021-60, WP74007390
Customer Repair Stories
Average Repair Rating: 2.3 / 5.0, 3 reviews.
What's this?
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Screws rusted solid
Had to drill out rusted screws to remove the surface plate. Then replace Orifices as the screws we're not able to be drilled out.
I took all the threads apart and added Gas pipe thread compound to the small ones and Gas thread tap for the larger ones on the back. This whole project was due to a little gas smell. None of the thr
... Read moreeads seemed to have compound.
To solve the screw issue from rusting again I bought #8 metal stainless steal metal screws 3/4" with Hex heads. The old ones were for wood and just zinc coated. I had to rethread all the Orifices including the new ones with a tap set. Do yourself a favor and do the #8 1/2" ones by the dials too. This should solve any rusting issues in the future. This worked well and is similar to their new setup. I hope this helps.
The ignitor switches are installed on top of the 4 gas valves for the range top. These switches control the electronic ignition. To replace the switch assembly the top of the range must be removed to gain access.
This was made more difficult by the fact that the screws that hold the burners to the range top were rusted and
... Read morehad to be drilled out so the the burners could be released from the top.
1. Disconnect the power to the range. 2. Open the top oven door. 3. Remove 2 - 1/4" sheet metal screws at the front corners of the range top assy. Remove the Burner knobs and the two Phillps screws that holds the gas valve assembly to the range top. 4. With a drill, remove the tops of the screws to release the burners from the range top. If the screws are in good condition and just unscrew them and the upper burners from the Orifice Holders. (I had to replace the orifice holders because the screws were stuck in them due to rust). 5. When the burners are free, lift the range top at the front and remove it from the range. Disconnect the ignitor wires from the ignitors on each holder. 6. To replace the Orifice Holders, disconnect the gas supply pipes from each holder by loosening the compression nut at the holder using an adjustable wrench. Secure the Orifice Holders when loosening the fittings, BE CAREFUL not to damage the aluminum gas supply pipes. 7. Note that there are 3 different Holders, be sure to use the holder that matches the specific location. 8. For LP gas fueled ranges ONLY, remove the small gas jets from the old holders and install them in place of the parts supplied with the new orifice holders. The new parts contain NATURAL GAS jets which are not compatible with LP gas. Each Different Orifice Holder uses a specific orifice or jet, make certain that the orifice matches the orifice holder. Check for leaks at the gas connections using soapy water. 9. Carefully raise the old ignitor switches (4) off the shafts of the gas valves. Note the top and bottom configuration of the switches 10. Carefully release the wires that come from the rear of the range from the rearmost switch. Press a suitable pin or other suitable tool in a the hole, beside the wire, just enough to release the wire. (Look at the NEW switch assemble to see how this works). Remove the wires from the NEW switch first to see how it is done. Repeat the process on the old switches. (you will re-use the wires that come up from the rear of the range. 11. Install the new switch assembly over the four (4) burner gas valves, take care to align the "D" shaped shafts with the holes in each valve. 12. Insert the wires in the two connections on the rearmost switch. CAUTION!!! Be sure to install the wires so that the color codes agree with the wires on the new switch assembly. Black to black and gray to gray. 13. Install the 4 clear plastic "shields" over the shafts and against the top of each switch. 14. Re-connect the ignitor wires to the burners and Re-Install the range top, in the reverse order of dis-assembly.
Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
39 of 46 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Screws Broke In Old Holder, Orifice
Just remove the old for new
Michael-peter from Valinda, CA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers
0 of 2 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
Next >
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
2 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Jack
August 15, 2017
I need the 2 front burner ignitor units are they both 16k? I put the top back on and from the pic i took it looks like the right burner may be different than the left.
For model number JDR8895AAS
Hi Jack,
Thank you for your inquiry. Both front burners are not the same. The right front orifice holder with spark igniter, part number PS11744613, is 12.5k. I hope this helps. Thank you and have a great day!
Can i just buy the spark igniter ps 11744613 12.5k that i need to replace the current one having problem ? Thanks.
For model number MGR6775BDB
Hi Patrick,
Thank you for your question. You can purchase a surface burner spark igniter separately from the orifice holder. The part number for the spark igniter is PS11746068. I hope this helps. Thank you and have a great day!