All Installation Instructions for Crosley Refrigerator CFD26WIS1

We had a broken bin on one of the doors.

We just slide in the bin.

Parts Used:

Door Bin (Clear)

Lorena from HOQUIAM, WA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Flipper mullion assembly broke

Removed 1 screw and unplugged flipper mullion assembly and removed it. Plugged in new flipper and one screw and done. Works as it should.

Parts Used:

Flipper Mullion Assembly

Cynthia from CIRCLEVILLE, OH
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

ice maker failure, broken auger housing

Remove ice maker, completely disassemble, being careful with the styrofoam around housing. This is a very weak part and takes much load from auger. Use a white, high strength tape to bind around the housing with, (very important) or you'll be doing this again as it is a failure point.

Parts Used:

HOUSING-CRUSHER

Don from NEW BERN, NC
Difficulty Level:
Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Ice Maker was making ice erratically

After sending PartSelect the info to their troubleshooting dept. about my ice maker, they recommended replacing the ice solenoid. I did so at a cost of $102. No change, turned out replacing the ice maker(did not purchase from PartsSelect) was the issue and works fine now.

So wasted $102. FYI the part took 6 days to arrive.

Parts Used:

Ice Maker Solenoid

Daune from OCALA, FL
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

1 Broken plastic mullion hinge. Mullion was not operating correctly.

Removed screw on Mullion so that the replacement hinge can slide onto the small plastic bracket on the door. Slid the mullion on the hinges and screwed in muliion (1 screw).

Parts Used:

Upper Or Lower Mullion Hinge Pin

Bernard from NEW WINDSOR, NY
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

2 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Previous seal had a tear and cold air was leaking around seal

Pulled the old seal out of the groove. Placed new seal in the groove. New seal has to be heated and massaged to get it into proper form so it does not leak. I have been continuously heating and massaging to get the seal to get it in the proper form. Been working on it for a week. Almost there.

Parts Used:

GASKET,FREEZER DRAWER,GREY

Daniel from Hampton, NH
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

GASKET WORN AND LEAKING

SIMPLY REMOVE THE OLD GASKET PULLING LIGHTLY BY HAND
THEN PUSHING THE NEW GASKET BY HAND

Parts Used:

GASKET-DR,MAGNETIC FF WH 36

Dennis from Lancaster, SC
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

A set scew was ordered twice.

The first order arrived in a huge box and there was no scew to be found, the box had wholes in it. I was given a refund and told to order again.

The repair did not happen and the set screw which was actually recieved the second time was returned because it was the wrong size.

Parts Used:

Screw

Susan from BRAINTREE, VT
Difficulty Level:
Very Difficult
Total Repair Time:
1- 2 hours

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

THE GASKET LOCKING INSERT DID NOT FIT THE BOTTOM OF THE DOOR.

I REMOVED THE OLD GASKET BEING VERY CAREFUL TO SEE EXACTLY HOW IT CAME OFF. I INSERTED THE LOCKING INSERT INTO THE TRACK IN THE DOOR WHICH DID NOT FIT AS THE OLD ONE DID. AFTER USING TREMENDOUS FORCE WITH MULTIPLE TOOLS I DID MANAGE TO GET THE TOP AND THE SIDES TO LOCK INTO PLACE AND EVENTUALLY HOLD. THE BOTTOM OF THE GASKET DID NOT HOLD SO I USED CLEAR CAULK AND TAPE TO HOLD THE GASKET IN UNTIL THE CAULK CURED. AFTER THE CAULK CURED THE GASKET HAS, SO FAR, REMAINED TIGHT.

Parts Used:

GASKET,FREEZER DRAWER,GREY

Robert from Lexington, SC
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

ICE WOULDN'T DISPENSE FROM ICE BOX

I read other suggestions trying isolate auger motor shaft with pliers while turning bar drive. needle nose pliers could hold the shaft. bar drive just would spin. so took the whole ice box assembly out
(only 2 screws) and with a metal cutting blade used the sawzall to cut along the shaft. freed it up enough to then unscrew it from that point. Left handed threads by the way.

Parts Used:

Drive Bar

James from ORLANDO, FL
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins

4 of 11 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

ice maker is stuck on crushed ice.

We had someone to come and look at it and we were told it was the solenoid valve. The repairman unstuck it for us and said when it does it again, he would have to order the part. We took it upon ourselves to order the part and DIY. We replaced the part that we were told was the problem and "guess what" it's still not fixed. It's still shooting out crushed ice. Will have to call repair guy back out here to see what we did wrong.

Parts Used: