Back
Back
Keep typing for more specific results...
Models > KDTE104ESS4 > Instructions

KDTE104ESS4 KitchenAid Dishwasher - Instructions

All Instructions for the KDTE104ESS4
31 - 45 of 521
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Old part never worked well, constantly got bumped by a part of the side when sliding rack back in (design flaw). When part got bumped and fell off, it also got warped from the heat, so then was even less likely to stay in place. New part fits more securely and doesn't bump the problematic part on
Just snapped it right into place! No tools required. Very easy!
Parts Used:
Dishwasher Tine Row Combo Retainer
  • JULIE from BOTHELL, WA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
13 of 17 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
No heating for washing or drying
Was a cinch just watched the video whole procedure took an hr or so
Parts Used:
Dishwasher Heating Element
  • Dewey from UNIONTOWN, AL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers
11 of 12 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The dishwasher quit circulating the water and cleaning the dishes it filled heated drained
The cost part plus shipping for each piece which was described as not cleaning properly due to not spraying. Each of these prices is part plus shipping, diverter valve $28.32 diverter motor did not fix the problem diverter motor $125.08 did not fix the problem my next option is the motor assembly which comes out to $311.53. I think they lead you on with the little parts and you work your way up with the big ones expense wise at this point I will simply cut my losses and buy a new dishwasher because I'm almost at what it would cost for a new one and I've had this one for 4 years. When I went to look for what the problem was each one of these said not cleaning properly which I think now is a generic term to just go from the smallest to the largest if I'm going to replace the motor for 300 plus dollars I might as well just buy a new washer
Parts Used:
Motor
  • Carol from HARRAH, OK
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
10 of 10 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Bottom Rack Wheel Assembly
Installation was very easy. The online video was excellent and clear.
Thanks
Parts Used:
Lower Dishrack Wheel
  • Albert from LIBERTY TWP, OH
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
11 of 13 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
dishwasher leaking from door
it was ok if I would have been sent the correct part, but you sent me the wrong part # and I had to go to the post office and mail it back. the part was not the same number as my order and completely wrong, still waiting for my refund and shipping charges. So you have failed me.
Parts Used:
Dishwasher Seal Brace
  • michael from TUCSON, AZ
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Socket set
14 of 22 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Noisy door
I found instructions on line when I goggled my dishwasher name and model number with the words noisy door. There were three or four good suggestions at a couple of the sites I visited. I tried applying vasoline, then silicone to the rope where it travels through the plastic guides but that just cut the sound down about 50%. My dishwasher has plastic guides that look like rollers but they don't turn, they are fixed in place. The ropes squeak as the pass over the guides. The replacement part kit has plastic guides that turn like wheels now so the rope does not drag over them and squeak. This repair could be done by me in 20 minutes or less every time now that I know what I am doing.

I removed the black bottom metal cover then turned the nuts on the adjusting (leveling) bolts to lower the front end of the dishwasher so I could pull it out of the cabinet. Once I lowered is as low as it would go I opened the door and pushed down on it which tilts the dishwasher down and you pull out on it and the top lip clears the cabinet. If your dishwasher just pulls out the first time you try these steps may not be necessary.
Once the dishwasher is out the guides and rope are down at the bottom in the front by the door. It's obvious what to do to replace them.
Parts Used:
Dishwasher Door Balance Link Kit
  • John from Minden, NV
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers, Wrench (Adjustable)
14 of 22 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replace lower dishwasher rack due to broken tines
Although the lower rack was a slightly different style than our original, it fit the dishwasher perfectly. We needed to transfer the silverware racks to the new rack and insert one set of removable tines. About 5 minutes and we are very happy with the repair.
Parts Used:
Dishwasher Lower Dishrack
  • Daniel from River Falls, WI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
12 of 16 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
wheel fell off
followed video instruction
Parts Used:
Lower Dishrack Wheel
  • Richard from BOSTON, MA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
12 of 17 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
rat got under dishwasher and chewed water lines, grommet
saw big hole in first (main) hose - got replacement at local hardware thinking it was the only problem - it wasn't - turned on the water and noticed another leak so ordered hose from parts select - fast delivery - installed 2nd hose but still a leak so ordered grommet from parts select - again prompt delivery - installed it and voila no more leak -
also checked for rat entry points, plugged those and put down bait - bait wasn't being taken under dishwasher even tho rat reappeared so put a snap trap in back - no luck so far - teachable moment: might have been cheaper to just get another dishwasher as parts are expensive and its difficult to tell extent of damage - luckily i only needed 3 parts = $150
Parts Used:
Dishwasher Hose
  • sharon from LAS VEGAS, NV
  • Difficulty Level:
    Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Pliers, Screw drivers
10 of 11 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
plastic parts degraded and failed
I pulled the rack and removed failed parts, then reassembled. I would note that the videos are helpful as dishwasher racks can be a bit of a puzzle.

Why manufacturers use so much plastic in a heated environment is beyond me. The heat cycle degrades the plastic to failure - poor design!
Parts Used:
Dishwasher Housing Dishwasher Upper Rack Adjuster
  • Edouard from DANBURY, CT
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
11 of 14 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Left and right upper dish rack slide track started losing bearings, plastic holding left side completely fell apart and top rack fell down. The upper rack adjuster also broke as a result.
Make sure you have everything you need before you start. The upper rack adjuster broke when the left track failed and needed to be replaced. Although only the left side track failed, the right side would have soon enough.

This repair was fairly simple. First, toggle the circuit breaker off and turn off the water supply under the sink. Remove gray plastic covers to expose and remove Phillips head screws on each side of inner door frame then remove plastic kick plate before sliding the dishwasher out roughly 20”. The insulation needs to be folded back (tab release back bottom corner) to expose the four rack fasteners on each side. A small socket bit (I used a slow speed hand drill) makes quick work of removing old tracks but make sure one hand is inside on the track to catch what’s left of it. Replace both tracks (the second will fail) arrow pointing up using the fasteners you removed. Reset the insulation and make sure water, drain and electrical connectors are all in good order before sliding dishwasher back and fastening side frame screws to adjoining cabinets (tip: use painter’s tape or similar to keep screw head connected to screwdriver). Replace plastic caps and the kick plate. I had to replace the upper rack adjuster before reinstalling the upper rack on the new tracks. Check the bottom filter and reservoir for any plastic bits or ball bearings and remove them before turning power and water back on. Enjoy not having to hand wash dishes again. For me, about 40 minutes.
Parts Used:
Dishwasher Dishrack Slide Track (Right Side) Dishwasher Dish Rack Slide Track (Left Side)
  • William from JACKSON, NH
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers, Socket set
9 of 9 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
water leaking from this appliance onto the floor
removed old gasket, installed new.
No Leaks!!
Saved the cost of a new dishwashers
Parts Used:
Dishwasher Door Seal
  • Raymond from AVONDALE, AZ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
10 of 12 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Wheel assembly broken
Very easy to repair with the replacement wheel assembly. Popped out the broken one, popped in the new one. Price was nothing compared to having an professional repair person come to the home. Glad I found you on line!
Parts Used:
Lower Dishrack Wheel
  • Daryle from WEYMOUTH, MA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
10 of 13 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Detergent dispenser latch broken
Replaced the detergent dispenser module by first unscrewing the front outer cover from the dishwasher and removing it, then by unplugging the old detergent dispenser, then by bending the metal latch clips outward to remove the old detergent dispenser, then by bending the metal latch clips inward before inserting the new detergent dispenser, plugging the new one into the wiring harness then re-securing the front outer cover of the dishwasher door.

This repair could be done in under 15 minutes but my dishwasher is so old that there was a lot of gunk built-up around the screws that hold the front cover on that I wanted to take my time cleaning up real nice.

The detergent dispenser is VITAL for getting dishes clean. Without it working properly, the detergent will be removed from the wash during the pre-wash/soak function and your dishes will not come out clean. I HIGHLY recommend doing this repair if your detergent dispenser is not working, and I had a great experience with www.PartSelect.com
Parts Used:
Detergent Dispenser
  • Benjamin from KNOXVILLE, TN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
9 of 10 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Lower dish rack needed replaced
Removed new from box and installed rollers as instructed that's all there was , very easy.
Parts Used:
Dishwasher Lower Dishrack
  • Lester from HARLINGEN, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
9 of 10 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the KDTE104ESS4
31 - 45 of 521