MGDX500BW2 Dryer - Instructions

remove back of dryer and install part same as old part was installed

Just like your video said. Very easy. I will purchase from you again. Thank you!!!!

I pushed one end of the catch on upper side the hole and when locked, I pushed the other end of the catch to the lower side to get locked. To complete, the white cover was inserted on top of the catch and done.

took out old ,twisted in the new one it was nice to have the right part the first time!! thank-you

Remove the protective cover on door with screwdriver, pop out the old catch, snap new catch in place, replace protective cover

Replaced door catch on dryer door. Followed video on Whirlpool website and it took less than 10 minutes. The dryer works great.

Kill power to dryer from breaker box.Remove lint filter & 2 screws. Take a flat head screw driver and place in gap between rash from corner of top panel & front panel of dryer and pry up to raise top panel of dryer & rest against wall the wall on angle do it doesn’t fall back toward you. Unplug wiring harness from dryer switch inside top front corner of dryer with outside of drum exposed when top panel of dryer is raised. Open dryer door and remove screws on each side of dryer switch located at upper inside corner of door opening. Take flat head screwdriver had slide in between connector & wiring harness on dryer. Remove old switch. Reconnect new dryer switch to wiring harness & remount switch to inside of dryer door opening. Lower top panel of dryer & press front corners of top panel to front panel of dryer & clips will be locked in place. Replace screws in dryer filter mounting holes yo top panel & replace dryer filter in place. Turn on power ‘ & check if light is working 1st. Then, turn timer knob clockwise, close door and listen if the drum is turning. Open door to see if drum turns. If both work, the job is complete.

Removed old seal and replaced with new one. Save yourself time and get some acetone to remove old glue works great!

Removing the old timer was the hard part. When pulling off one of the wires it broke off from the female connector inside the plastic piece. I had to go the store to find another very small female connector that would work inside the plastic. After stripping the very small stranded wire, crimping it to the new connector I finally could insert it inside the replacement timer.
Upon completion, nothing had changed. Still have heat but the timer does not move. An electrician friend says the dryer probably has a 110 wire coming off the 220 to supply the power to the timer. I haven't taken it apart yet to try and find the problem.

It went well, I followed the instruction video and referred back to it if any questions or difficulty. The instructor on the video was obviously very experienced and duplicating his actions exactly was very helpful, One thing I noticed that wasn't mentioned was that the thread on the wheel / motor is left handed.

Easy repair. Bought replacement parts on Amazon and they lasted 1month. Should have purchased from you in the first place. Re replaced with your parts and no issues.

I followed the very informative video and wrote down step-by-step notes for myself. The repair went very smoothly. The only thing I didn't realize, was that the dryer has 4 rollers, not just 2 shown in the video. All are easy to access once you disassemble. I had to do it twice since I had to order 2 more rollers in order to replace them all. Also, the triangle plastic washers come with the roller, so you won't need to order them separately like I did. I also changed the idler pulley roller while I was in there since that has bearings too. Just as easy. I'm very happy with my quiet dryer! One last note: The new rollers are a bit louder than normal at first, but they quiet down very quickly as you use the dryer. It must be because they are brand new.

Watched the videos available. Opened the top and saw tub jumping. Unplugged and removed front panel. Saw tub rollers were broken or melted. Removed tub watched more videos, and installed the felt belt I got from PartsSelect. Trouble removing the tub rollers, but finally got them off. The axles had a sticky residue which I removed with 220 grit sandpaper. I installed new rollers I had bought locally. Reassembled dryer. Worked quietly and smoothly, and it no longer shut itself down. Worked well for one day when it started.s loud noise with bumping. I found both rollers had lost their outer rim , and the tub was running on hard plastic and there was sticky residue back on the ankles. I stopped there.

The original door catch had broken and would no longer stay shut. Ordered the part from this site with ease. Very easy to replace the broken door catch on my Amana dryer. Tool needed was a flat head screwdriver to loosen the cover, remove broken piece and easily replace with new part. Followed the video and it was back to normal operation within minutes.

Once I received the new latch I removed the latch cover with the flat head screw driver and worked out the old latch. I then positioned the new latch and snapped in place. I then replaced the cover and shut the Dryer door. The door latched and the repair was complete.