Infinite Burner Switch - Small Element - 240V Specifications
This is a part for your range. This switch controls the stovetop surface burner. If you notice that your stove top is not turning on or is not adjusting to the corresponding desired heat, it is mostly likely due to the burner switch needing to be replaced. You will need a #1 square-head screwdriver and needle-nose pliers. Disconnect the power from the range. You will need to move the range out from the wall to remove the upper back panel to access to this part. This is an OEM genuine part.
How Buying OEM Parts Can Save You Time and Money
Part Videos
Replacing your Frigidaire Range Infinite Burner Switch - Small Element - 240V
Troubleshooting
This part fixes the following symptoms:
Element will not heat | Will Not Start
This part works with the following products:
Range.
Part# 316436000 replaces these:
AP3890378, 1155394, 316021500, 5304506424
Customer Reviews
Average Rating:
★★★★★
★★★★★
9 Reviews
4.1
Filter By Rating:
5 Stars
7
4 Stars
0
3 Stars
0
2 Stars
0
1 Star
2
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Christo S - September 18, 2022
Verified Purchase
Working Oven Again!
Installed the new Infinite Burner Switch from PartSelect.
Oven works again!
Saved $900 from not having to buy a new oven
Thank you PartSelect!!
★★★★★
★★★★★
Christine M - January 16, 2022
Verified Purchase
Easy repair!
The part was shipped within a few days. Easy to replace the old infinite switch.
★★★★★
★★★★★
Delbert T - July 8, 2020
Verified Purchase
the part worked quite well and was easy to install.
Even though there was some delay in shipping due to the current Covid-19 pandemic, this part and two others ordered earlier, arrived on the date PartSelect advised. I will use them for future orders as well.
★★★★★
★★★★★
Gayle B - July 9, 2019
Verified Purchase
Kenmore Electric stove
Part for stove came SuperFast! Fixed the problem. Easy fix.
★★★★★
★★★★★
Kevin D - June 7, 2019
Verified Purchase
Straightforward
The part is slightly different size/color than the OEM, but installed easily and is working perfectly.
The wire terminals have letters molded into the body of the part which correspond with letters on the OEM body, so just be sure to transfer each colored wire one at a time between their matching letter codes. Good to go!
★★★★★
★★★★★
Louie B - April 27, 2019
Verified Purchase
I love the part and convenience, but unfortunately the part doesn’t have the same wiring placement.
Could you help me in establishing were the wires hook onto the new switch? The new switch has the same number of terminals as the old one but in a different configuration. Also the numbers on the terminals of the new switch don’t match anything on the old one.
The new switch has the numbers: 4-H2, 5-L2, 3L1, 1-H-1, 2-P on the five terminals while the old switch has one blue, one green, two together purple, two together black wires with one having a blue stripe and two red wires together, make a total of also five terminals on the old switch. Now if I only knew which wires to plug into the new from the old!
★★★★★
★★★★★
Dante M - October 24, 2018
Verified Purchase
No so easy !
Switch arrived on time it needed to be installed the way it is in photo on left in doing so I had gotten confused keeping knob in up position I switched wires and burned switch video did explain it but I put black & purple wire on wrong terminals ! Down the road I will try again some other time ! (no color code on terminals also not same as old switch positions)
★★★★★
★★★★★
Robert A - August 7, 2018
Verified Purchase
works perfectly.
Thank you all very much for your help in getting me the right switches. Apparently the first switches were for the large burners, these switches (and the small burners) now work just like new. (wish I could put a smiley face here, y'all earned one) Thanks again and God Bless You.
★★★★★
★★★★★
Timothy S - February 27, 2018
Verified Purchase
easy repair
Switch fit and finish are like factory. Super easy to install, only took minutes and works like new again. I did all four switches, price was great, delivered fast and on time.
< Prev
1
Next >
Customer Repair Stories
Average Repair Rating: 3.3 / 5.0, 11 reviews.
What's this?
Sort by:
< Prev
1
2
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
The front left dual element stopped regulating temperature
Replaced the dual element switch and that fixed it up
Both front burners began heating too fast and too high. One damaged the finish on the splash pan.
At the Frigidaire parts website, I found the parts and saw that there are videos that show how to replace the burner controls. In brief: 1) Slide the range/oven out so you can get to the back of the control hood. 2) There are three screws that hold the cover in place (the video showed four). 2a) The video also suggests usin
... Read moreg a #1 square bit. I found that there was indeed a square hole in the caps of the screws, but they also had a hex head that a 1/4" hex nut driver fits. So I used that. 2b) Be careful taking out the last (top center) screw. When it comes free, the cover can drop and bruise or cut your foot or the floor. Having a helper is worth it! 3) The switch for the larger elements has a red dot on front and back. Match it with the one in place that has a red dot. The switch for the small element doesn't have a dot. 3a) Holding a new switch in your hand, remove one wire at a time from the switch in the control hood and put it in the same place on the new switch. I found that for my stove, there was a fixture holding two wires and another holding three wires. This made it impossible to put the wires on wrong. 3b) When all wires have been transferred, pull off the control knob in front and unscrew the two screws that hold the old switch in place. Take out the old switch and replace it with the new switch. 3c) Use the two screws to attach the new switch in its place and replace the control knob. 4) Repeat for as many switches as you purchased. I did all four. 5) Replace the cover. 6) Slide the range back into place.
I found black deposits on all the switches, that must have come from a contactor inside, so I was glad I replaced them all.
Another tip: while the unit is out, clean off the sides and back that you couldn't get to while it was in place. For us, this took as long or longer than the steps above for replacing the switches.
Long filter didn't fit, excessive plastic flashing, poor quality
hand tried flashing, still did not fit well. Too large. Appears to be made from worn out mold. No instructions included with burner controller, it would have been helpful to have a wiring diagram as the new controller did not match old. Once wired, controller works great
Old part was replaced by mfg’r. Wiring different. No drawings or any info was included to show wiring.
I was forced to call in a pro repairman. Will cost me at least $150 for part and repairman. I could have done job if instructions on how to rewire had been included.
Nelson from FRUITHURST, AL
Difficulty Level:
Difficult
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers, Socket set
2 of 2 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
my burners would just heat up solid red even when i had controls turned down to 2 or 3. i would have to turn controls off and back on, then they still would just go back to glowing red
This was my first time ever working with electrical issues. My husband is not physically able to do repairs now. Very easy fix. Just viewed video repair instructions and it went exactly as instructed. Within 45 minutes, I had my stove repaired and cleaned and back in working order!! Great results. My range is working perfectly again and M
... Read moreama is happy!!
After a brief discussion with CS about the electric stove part was shipped it arrived and I proceeded to install I found it needed to be installed sideways not up & down like the old one. The terminals did not line up so I put the black lead first and the purple lead last in doing that I burned out the switch??? was not easy to install as
... Read more the video showed his switch matched each wire? My installation was sideways??
Read less
Dante from SOUTHOLD, NY
Difficulty Level:
Difficult
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers
2 of 2 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Burner switch work sometime.
I follow the video on your site
junius from WICOMICO, VA
Difficulty Level:
Really Easy
Total Repair Time:
1- 2 hours
Tools:
Nutdriver
3 of 4 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
new switch was not wired like old one
i first replaced element after old smoked & quit. replaced switch but i noticed when i started to replace the wires one at a time something didn't seem right. after checking the #s on the old one, they didn't match up with the new one.luckily i had the stove diagram from a packet on the back of the stove. i traced each wire according to
... Read more the diagram and everything worked out fine. i'm just glad i didn't replace each wire to wire.the #'s were on the switch where each wire went which was different than the org. even though they looked the same.
Read less
PERRY from LECANTO, FL
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
20 of 32 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
the indicator light for burners broke and shorted agaist the back panel on range
This caused the burner switch cotacts to arc burning out the switches. It took 30 or 43 minutes to replace the switches and put the range back together. The bake element took 10 min. ti replace. Grandma has her range back and I am a happy grandpa!! Thanks for the help and we saved over $170.00 for the repairs. Jim Johnson
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
24 questions answered by our experts.
Sort by:
< Prev
1
2
3
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Adolfo
October 23, 2017
One of the large burner is very hot, even the switch is at minimum.
For model number FEF352DWA
Hi Adolfo, Thank you for the question. When the element is not keeping the proper temperature, you will need to replace the burner control switch.Hope this helps!
27 people found this helpful.
Was this helpful?
Thank you for voting!
Pedro Barrera
December 21, 2018
Does this switch come with a control knob?
For model number fef316BSF
Hello Pedro, thank you for your question. The knob does not come with the switch it is sold individually. That part number is PartSelect Number: PS439834. I hope this helps!
7 people found this helpful.
Was this helpful?
Thank you for voting!
Carl
August 25, 2017
Once the burner is hot and then the knob is turned down, the burner will keep heating up. Will this part fix that issue or is there another? Thanks.
For model number FEF352FSE
Hi Carl,
Thank you for your question. I would actually suggest testing your burner, switch, and wire between the switch. Either one of these parts could be causing that issue. You can test your burner and switch with a multi-meter. Good luck with your repair.
5 people found this helpful.
Was this helpful?
Thank you for voting!
Mattie
July 15, 2019
Is a switch need for all burners
For model number TEF351EWN
Hi Mattie, thank you for your question. I have listed both types of switches below for you. You need two of each. Good luck with your repair.
We have lost heating to both the stove elements and oven. When you turn the stove top elements to a off position then turn back on there is a clicking noise then all power stops.
For model number FEFL67DCJ
Hello Russ, Thank you for your inquiry. We would recommend checking the following parts to fix your issue: the burner switches, the wiring harness, the main control board, and the temperature sensor. You can test the parts with a multimeter. If you are unfamiliar with how a multimeter functions, there are YouTube videos available to assist you. Hope this helps!
3 people found this helpful.
Was this helpful?
Thank you for voting!
Rod
November 9, 2019
Top elements sometimes go full-on and will not turn off CFEF366EMG.
Has also been known to turn on low and still go on high heat, these problems are intermittent.
For model number CFEF366EMG
Hello Rod and thanks for writing.
The surface element switch sends voltage to the surface element coil. Sometimes, when the surface element switch fails, the electrical contacts inside the switch fuse together, causing the switch to send continuous voltage to the surface element. If the surface element switch is defective, replace it. We hope this helps. Please contact us at any time
3 people found this helpful.
Was this helpful?
Thank you for voting!
Jim
December 8, 2019
Looking for the correct burner switch for ffef3018lbd
For model number Ffef3018lbd
Hello Jim,
Thank you fro your question. The burner switch for the back left and right small burners is under part PS1145039 for your model, the front left burner switch is under part PS3504401, and the front right burner switch is under part PS1145040 for your model. Hope this helps!
While cooking on the burner I heard a loud pop and then it quit working completely. The light comes on when I turn the knob but the burner will not work. Could it be this part or the element?
For model number GLEF384HBA
Hello Tayra, Thank you for the question. If the light comes on, this normally means it is a issue with the element. Only way to know %100 before placing an order is to test the continuity with a Multi Meter. Thank you for your inquiry, good luck with this repair!
3 people found this helpful.
Was this helpful?
Thank you for voting!
Bobby
April 15, 2018
My 6 inch burner will heat up by its self, with the switch off. Causing my hot surface light to stay on. Element looks good. Do i need a switch? Thanks
For model number FEFL79DBL
Hi Bobby,
Thank you for your question. It could be your switch. The two parts that you generally check when having an issue like this is your burner itself or the burner switch. You can test both parts with a multi meter to be sure if you wanted. I hope that helps. Good luck with your repair.
2 people found this helpful.
Was this helpful?
Thank you for voting!
Jeff
October 30, 2019
Infinite burner switch for large burner needs replacing on Kenmore diagram it is #54 on your diagram it is 54a but i need one for the large element both your items for sale say small element so which fo i order
For model number 790.94153310
Hello Jeff, thank you for inquiring. You will need the Infinite Burner Switch, part number PS1145040 for your range. Good luck with your repair!
